We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Blue 4-port SATA cable with braided sleeve, 0.5m

YEPLOOK

YEPLOOK 4 SATA To 4 SATA Cable 0.5m Blue

SKU CH-PQF7-1W928

Connects four SATA drives at 6 Gbps with a 0.5 m blue braided cable supporting hot-swap

  • ColorBlue

Cable Length 1.6 Feet

  • Connect up to four drives with one cable using the 4 SATA to 4 SATA design
  • Transfer data at up to 6Gbps with SATA 3.0 support
  • Hot-swap drives without shutting down thanks to plug-and-play SATA interface
  • Braided nylon mesh keeps wiring tidy and ventilated inside the case
  • Short 0.5 m length suits compact server and multi-drive builds

4 SATA to 4 SATA cable for multi-drive servers

This blue 0.5 m cable links four SATA drives to a single host port using 7-pin connectors rated for 6 Gbps. It is built for administrators who need to add several drives to a server or workstation without occupying extra backplane slots. The straight heads with locking shrapnel keep each connection secure during drive swaps.

Thermals noise and power in normal use

The cable draws no external power and adds no active cooling, so it produces no audible noise and negligible heat inside the chassis. Its high-quality nylon braided mesh keeps the four runs separated for better airflow around dense drive bays. Signal integrity is maintained at the full 6 Gbps rate across the 0.5 m length.

Braided mesh and hot-swap support change daily

The braided sleeve bundles the four channels into one tidy loom that resists snagging on neighbouring components during maintenance. Hot-swap capability lets technicians replace individual drives without powering down the host system. Plug-and-play operation means no driver installation is required on any SATA 7-pin host.

Highlights

  • Connect up to four drives with one cable using the 4 SATA to 4 SATA design
  • Transfer data at up to 6Gbps with SATA 3.0 support
  • Hot-swap drives without shutting down thanks to plug-and-play SATA interface
  • Braided nylon mesh keeps wiring tidy and ventilated inside the case
  • Short 0.5 m length suits compact server and multi-drive builds

Specifications

Model4 SATA TO 4 SATA
ColorBlue

Other versions of this model

2 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

How do I install the 0.5 m SATA 3.0 cable with its straight 7-pin connectors?

Align each straight 7-pin plug with the SATA port on the drive and motherboard, push straight in until the metal latch clicks, and avoid angling the connector — the most common mistake is forcing it at an angle and bending the pins.

Will the blue nylon-braided 0.5 m cable need any maintenance or replacement over time?

The braided mesh resists abrasion and keeps airflow tidy; no scheduled maintenance is required, but replace the cable if the latch tabs snap off or the connectors become loose after repeated hot-swap cycles.

What limit appears first when the cable runs sustained 6 Gbps transfers on a 10,000 rpm drive?

The 0.5 m length keeps signal loss minimal, so the practical ceiling is the SATA 3.0 6 Gbps interface itself rather than cable attenuation.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.