We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Weller LT series chisel soldering tip, 4.6 mm wide, 0.8 mm thick, 13 mm long, iron-plated copper finish

Weller

Weller Soldering Tip Chisel 4.6 mm LT Series 0.8 mm Thickness 13 mm Length

SKU CH-F7T7-7T2CP

Iron-plated copper chisel tip, 4.6 mm wide and 13 mm long, fits Weller WP 80, WSP 80 and WXP 80 handpieces on WD1002 and WR series stations

  • TypeWelding Parts & Supplies
  • Chisel tip reaches 850 °F for rapid heat transfer
  • 6 mm width and 0.8 mm thickness suit fine-pitch joints
  • 13 mm length fits tight board clearances
  • Compatible with Weller WP 80, WSP 80 and WXP 80 handpieces
  • Works with WD1002, WR2000VX and WR3000 series stations

Weller LT Chisel Tip 4.6 mm

This Weller LT series chisel tip measures 4.6 mm wide and 13 mm long with a 0.8 mm thickness. It fits Weller handpieces including the WP 80, WSP 80, WSP 80N and WXP 80. The iron-plated copper construction supports a maximum operating temperature of 850 degrees Fahrenheit. It is designed for general soldering applications on compatible stations.

Limited to LT-Series Handpieces and Stations

The tip only works with the LT series interface on the listed Weller handpieces and stations such as the WD1002, WR2000VX and WT1012 models. It will not fit other Weller tip series or non-Weller handpieces. The chisel geometry suits flat joints but is less suited to fine-pitch or drag-soldering tasks. Buyers needing different tip shapes or series compatibility must choose another part.

4.6 mm Chisel Width Decides Fit and Joint Coverage

The 4.6 mm chisel width determines the contact area and heat transfer for each joint. If your work requires a narrower or wider tip, this model will not match the application. Verify the required width against the component pitch before ordering. No other specification overrides this single dimension for selection.

Highlights

  • Chisel tip reaches 850 °F for rapid heat transfer
  • 6 mm width and 0.8 mm thickness suit fine-pitch joints
  • 13 mm length fits tight board clearances
  • Compatible with Weller WP 80, WSP 80 and WXP 80 handpieces
  • Works with WD1002, WR2000VX and WR3000 series stations

Specifications

BrandWELLER
TypeWelding Parts & Supplies

Questions about this item

What does the 4.6 mm chisel width mean for the joints I can solder?

The 4.6 mm chisel face delivers a broad contact area, making it efficient for larger pads, through-hole connectors and ground-plane work where a narrower tip would lose heat too quickly.

How does the 850 °F maximum temperature behave on a live station?

The tip is rated for 850 °F peak; the connected station regulates actual tip temperature, so you set the desired value on the station and the tip reaches it without overshooting the 850 °F limit.

Which stations and handpieces does the LT series tip fit?

It fits Weller WD1002, WD1002T, WR2000VX, WR3000M, WR3000SA, WR3000TA, WT1012, WT1013 and WT1013N stations when used with WP 80, WSP 80, WSP 80N or WXP 80 handpieces.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.