We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
M12 threaded inductive sensor chrome-plated brass barrel cable connection

Turck

Turck BiM-M12E-AG4X 4430200 inductive sensor M12 90 mm 10-65 VDC 2-wire NO contact 107 g

SKU CH-8A1X-RFCC9 MPN BiM-M12E-AG4X

M12 inductive sensor detects metal at 90 mm on 10-65 VDC two-wire NO output

  • TypeTest Equipment
  • Item Count1 pack
  • Selling UnitBox
  • Parts3 Years
  • Labor1 Year
  • 90 mm sensing range with DMR31-15-5 magnet
  • 10–65 VDC supply voltage for flexible power
  • 2-wire NO contact simplifies wiring
  • Chrome-plated brass M12 × 1 housing
  • 107 g weight for easy mounting

Industrial Inductive Sensor

The Turck BiM-M12E-AG4X is a magnetic-inductive proximity sensor built for industrial automation and position-sensing tasks. It detects ferrous targets through a 90 mm rated switching distance using a DMR31-15-5 magnet. The M12 × 1 threaded barrel allows direct mounting into standard fixture holes. Electrical and maintenance teams specify it for reliable non-contact detection in machinery, conveyors and process equipment.

10–65 VDC Two-Wire Operation

The sensor runs on a 10 to 65 VDC supply with a polarised two-wire output, simplifying wiring in control cabinets and field junction boxes. Normally-open contact logic delivers a clean switching signal without auxiliary power leads. Chrome-plated brass housing and fully encapsulated electronics resist oil, coolant and vibration, keeping leakage current low and thermal drift minimal across the operating range.

Cable Connection and Magnet Pairing

A fixed cable tail provides the electrical connection, removing the need for separate connectors or field-wireable plugs. The 90 mm sensing specification is achieved only when paired with the DMR31-15-5 magnet, so the accessory must be ordered together for correct operation. The 107 g unit ships in a single pack with three-year parts and one-year labour coverage from the manufacturer.

Highlights

  • 90 mm sensing range with DMR31-15-5 magnet
  • 10–65 VDC supply voltage for flexible power
  • 2-wire NO contact simplifies wiring
  • Chrome-plated brass M12 × 1 housing
  • 107 g weight for easy mounting

Specifications

BrandTURCK
ModelBiM-M12E-AG4X 4430200
TypeTest Equipment
Item Count1 pack
Selling UnitBox
Parts3 Years
Labor1 Year

Questions about this item

How do I mount the M12 × 1 threaded barrel and where must the DMR31-15-5 magnet sit for the 90 mm switching distance?

Screw the chrome-plated brass barrel into an M12 × 1 tapped hole or nut; the magnet must face the sensing face at the rated 90 mm distance, aligned on the barrel axis, otherwise the magnetic-inductive field will not trigger the NO contact.

What part will need replacement first and how often should I check the cable?

The 2-wire cable is the only wear item; inspect the jacket and conductor entry at the sensor body every 12 months for abrasion or oil ingress, and replace the cable if the insulation shows cracks.

At what voltage or temperature does the 2-wire output start to drop out during continuous operation?

The sensor is rated for 10…65 VDC; if the supply falls below 10 V or the cable resistance adds enough drop to push the sensor under that threshold, the NO contact will stop switching reliably.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.