We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Copper desoldering braid on spool, 2.0 mm wide, 1.5 m length

Transway's Marketplace

Transway's Marketplace CP-2015 2.0MM Desoldering Copper Braid Solder Remover Spool Flux Wick Wire Cable

SKU CH-5T9E-W75TN

Removes solder with 2.0 mm copper braid, 1.5 m length, suited for Sn60 and Sn63 alloys

  • Type2.0MM Desoldering Copper Braid Solder Remover Spool Flux Wic
  • Size/Dimensions2.0MM
  • Material2.0MM
  • Selling UnitEach
  • Features2.0MM
  • 0 mm width targets fine-pitch joints
  • 5 m length provides many desoldering operations
  • Flux-impregnated copper braid absorbs solder on contact
  • Works well with 60 % and 63 % tin alloys
  • Cut-and-discard used sections for clean repeat use

2.0 mm Desoldering Braid for Solder Removal

This 2.0 mm copper desoldering braid removes excess solder from circuit boards and component leads. The spool holds 1.5 metres of flux-coated wick, supplied as a single CP-2015 unit. It is intended for technicians and hobbyists who need to clean joints during repair or rework.

Suited for through-hole

The 2.0 mm width fits standard through-hole pins and wider SMT pads, absorbing molten solder when heated with an iron. It is less suitable for very fine-pitch IC legs or dense BGA arrays where a narrower braid would be required. Users working exclusively on micro-scale boards should consider a smaller width.

2.0 mm width determines joint compatibility

The braid measures 2.0 mm wide, which dictates the maximum contact area it can cover in a single pass. This dimension decides whether the wick can draw solder from the target joints without bridging adjacent pins. The 150 cm length provides multiple uses before replacement.

Highlights

  • 0 mm width targets fine-pitch joints
  • 5 m length provides many desoldering operations
  • Flux-impregnated copper braid absorbs solder on contact
  • Works well with 60 % and 63 % tin alloys
  • Cut-and-discard used sections for clean repeat use

Specifications

Type2.0MM Desoldering Copper Braid Solder Remover Spool Flux Wick Wire Cable
Size/Dimensions2.0MM
Material2.0MM
Selling UnitEach
Features2.0MM

Questions about this item

How do I install the 2.0 mm desoldering braid and what step do people often miss?

Place the braid over the joint, press the hot iron tip onto it until the solder is absorbed, then lift both together; the step many miss is cutting off the used section with nippers before the next joint.

What maintenance or replacement will the CP-2015 braid need later?

The braid is single-use; once a section is saturated with solder it must be snipped off and discarded, so you simply pull fresh length from the 1.5 m spool as needed.

What limit appears first during sustained desoldering with this 2.0 mm flux wick?

Absorbability drops when the flux is spent or when the solder alloy differs; the supplier notes Sn 63 % and 60 % tin solders absorb well, while other alloys may saturate the braid faster.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.