We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Cylindrical M18x1 nickel-plated brass sensor, 67 mm long, 2 m PVC cable

Sick

Sick IME18-05BPSZW2S Inductive Proximity Sensor PNP 5 mm M18x1 2 m Cable IP67

SKU CH-NR5M-KXF7W

An M18 flush-mount inductive sensor detects metal at 5 mm with a PNP normally-open output on a 2 m PVC cable

  • 5 mm sensing range with flush mounting
  • PNP normally-open output on 10–30 V DC supply
  • IP67 nickel-plated brass housing resists dust and water
  • 1,000 Hz switching frequency for fast detection
  • 2 m PVC cable with 3 × 0.25 mm² conductors

Flush-mount M18 inductive sensor

The Sick IME18-05BPSZW2S is a cylindrical inductive proximity sensor with a flush mounting style and a 5 mm sensing range. Its PNP normally-open output suits DC control circuits that need a positive switching signal. The 10 V DC to 30 V DC supply range fits standard industrial power rails. This sensor targets automation engineers who need reliable metal detection at close range.

IP67 enclosure and 1000 Hz switching

The IP67-rated nickel-plated brass housing resists dust and temporary immersion while operating between –25 °C and +75 °C. A 1000 Hz switching frequency supports fast cycling applications. Current consumption sits at 10 mA with a 200 mA continuous output capability. Voltage drop stays at or below 2 V and the unit tolerates up to 10 % supply ripple.

2 m PVC cable and 40 Nm tightening torque

A 2 m three-wire PVC cable with 0.25 mm² conductors exits the housing for direct wiring without separate connectors. The M18 x 1 thread length is 52 mm and the maximum tightening torque is 40 Nm. Short-circuit, reverse-polarity and power-up pulse protection are built in. The sensor carries UL file NRKH.E181493 and meets EN 60947-5-2 EMC requirements.

Highlights

  • 5 mm sensing range with flush mounting
  • PNP normally-open output on 10–30 V DC supply
  • IP67 nickel-plated brass housing resists dust and water
  • 1,000 Hz switching frequency for fast detection
  • 2 m PVC cable with 3 × 0.25 mm² conductors

Specifications

BrandSICK
ModelSICK IME18-05BPSZW2S

Questions about this item

How do I mount the M18×1 flush sensor and what torque mistake should I avoid?

Thread the nickel-plated brass barrel into an M18×1 cut-out until the 52 mm thread length seats flush, then tighten to no more than 40 Nm — exceeding that torque can deform the housing and shift the 5 mm sensing face.

Which part of the 2 m PVC cable will likely need attention first in a high-vibration line?

The Ø 3.9 mm PVC jacket and 0.25 mm² conductors at the cable-entry point absorb the 30 g shock and 10–55 Hz vibration; inspect that strain-relief area regularly and replace the cable if the jacket cracks or conductors fatigue.

At what ambient temperature does the 5 mm sensing range drift beyond the 4.05 mm safe zone?

Temperature drift is ±10 % of the sensing range, so at the extremes of –25 °C or +75 °C the effective range can shift by 0.5 mm, pushing the reliable detection limit past the 4.05 mm safe sensing distance.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.