We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Round silver metal magnet 36 mm diameter with threaded eyebolt attached

Baldwin 36 mm Neodymium Fishing Magnet 150 Lbs 68 KG Pulling Force with Eyebolt

SKU CH-APD8-QD9J8

A 36 mm neodymium fishing magnet with an eyebolt delivers 150 lbs pulling force for underwater retrieval and lifting tasks

  • MaterialMetal
  • Compatibility/FitmentAdhesives; Enamels; Epoxies
  • Lifting Capacity1000 pounds
  • Pull Capacity1000 pounds
  • 150 lbs pulling force for retrieving heavy ferrous objects
  • 36 mm neodymium core concentrates magnetism at the base
  • Triple Ni-Cu-Ni coating resists rust and chipping
  • Countersunk hole plus eyebolt enables versatile attachment
  • Manufactured under ISO 9001 quality systems for consistent performance

36 mm Neodymium Fishing Magnet

The Baldwin DHDL36mm is a 36 mm diameter neodymium fishing magnet rated for 150 lbs (68 kg) pulling force under ideal conditions. It features a countersunk hole with an included eyebolt for secure rope attachment. The magnetic face is concentrated at the bottom while the steel cup shields the sides. This tool suits magnet fishing, lifting, and retrieval of ferrous objects in rivers, lakes, or workshops.

Upgrading from weaker retrieval magnets

Magnets with lower pull ratings or unshielded designs lose holding power on thicker or rusted steel. The 150 lb rating and triple-layer Ni-Cu-Ni coating make the jump worthwhile when targets include heavier debris, deeper water, or repeated use where coating wear matters. The permanent neodymium core retains magnetism for decades without recharging. Buyers needing more than 1000 lbs lift capacity or non-ferrous metal detection cannot use this magnet.

Check your setup before ordering

Verify the eyebolt threads match your rope or carabiner hardware. Confirm the mounting surface is clean, flat, and made of pure iron or mild steel for maximum adhesion; paint, enamel, epoxy, or corrosion reduce effective pull. Ensure the 1.42 inch diameter clears any access holes or pipe interiors you plan to probe. The magnet is new and manufactured under ISO 9001 quality systems.

Highlights

  • 150 lbs pulling force for retrieving heavy ferrous objects
  • 36 mm neodymium core concentrates magnetism at the base
  • Triple Ni-Cu-Ni coating resists rust and chipping
  • Countersunk hole plus eyebolt enables versatile attachment
  • Manufactured under ISO 9001 quality systems for consistent performance

Specifications

BrandBaldwin
MaterialMetal
Compatibility/FitmentAdhesives; Enamels; Epoxies
Lifting Capacity1000 pounds
Pull Capacity1000 pounds
Part NumberDHDL36mm

Questions about this item

What diameter clearance does the 36 mm magnet need to sit flush against a surface?

The magnet body is 36 mm (1.42 inch) in diameter, so the mounting face must provide at least that wide a flat contact area for full pull force.

How is the eyebolt secured to the countersunk hole, and what step is often missed?

Thread the supplied eyebolt into the countersunk hole until the shoulder seats fully; the step often missed is tightening it firmly so the load transfers to the steel cup, not the magnet face.

When should the Ni+Cu+Ni coating be inspected or the magnet replaced?

Inspect the triple-layer coating after each use in water; replace the unit if the coating is chipped, cracked or shows rust, as damage exposes the neodymium core to corrosion.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.