We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in

Aomoproing

Aomoproing Mini SAS SFF-8087 to 4 SATA 90 Degree Breakout Cable .5m

SKU CH-ARQ6-47T7F

Connects a Mini SAS 8087 host to four 90-degree SATA drives with 6 Gbps bandwidth and 1.64 ft length

Cable Length 0.5m

  • Connects RAID controller to four SATA drives via SFF-8087 36-pin interface
  • 90-degree angled SATA connectors ease routing in tight server chassis
  • Supports 6Gbps per port for high-throughput storage arrays
  • 64 ft length with woven mesh sleeve protects half the cable run
  • Tinned copper 30 AWG drain wire maintains signal integrity across PCIe 2.0 x8 lanes

Connectivity & Use Case

This 0.5 metre Mini SAS SFF-8087 to 4 SATA breakout cable links a RAID or PCIe controller with an SFF-8087 port to four SATA drives. It suits builders adding direct-attached storage to a server or workstation that uses a compatible host bus adapter. The forward pin-out design connects the controller host to target backplanes or drive cages. It is not for external enclosures or controllers lacking an internal SFF-8087 connector.

Thermals Noise & Power

The passive cable assembly draws no power and adds no audible noise to the system. A woven mesh sleeve covers half the length for protection and easier routing without trapping heat. Tinned copper drain wires at 30 AWG provide shielding to maintain signal integrity at 6 Gbps per port. No active cooling or external power is required.

Deciding Specification

Each of the four SATA ports supports up to 6 Gbps data transfer rate when paired with a compatible controller. The 36-pin SFF-8087 male plug uses latch locking, while the four 90-degree SATA female connectors also latch for secure attachment. Cable length is 1.64 feet (0.5 metre) with blue jacket and black sleeving. P1 to P4 markers simplify drive identification after installation.

Highlights

  • Connects RAID controller to four SATA drives via SFF-8087 36-pin interface
  • 90-degree angled SATA connectors ease routing in tight server chassis
  • Supports 6Gbps per port for high-throughput storage arrays
  • 64 ft length with woven mesh sleeve protects half the cable run
  • Tinned copper 30 AWG drain wire maintains signal integrity across PCIe 2.0 x8 lanes

Specifications

No published specifications for this item yet.

Other versions of this model

3 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

How do I install the SFF-8087 to 4 SATA breakout cable and which step is often missed?

Plug the 36-pin SFF-8087 male end into the RAID or PCIe controller until the latch locks, then attach each 90-degree SATA female connector to a drive backplane; the step people miss is verifying all four P1-P4 markers match the intended drive bays before securing the woven mesh sleeve.

What maintenance or replacement will this 0.5 metre cable need over time?

The tinned copper drain wire and latch-locking connectors are rated for the cable's service life; only replace the assembly if the blue jacket shows abrasion, a latch fails to click, or a drive drops from the array due to intermittent contact.

What limit appears first when the cable runs sustained 6 Gbps transfers on four drives?

The shared PCIe 2.0 x8 host link caps aggregate throughput at roughly 4 Gbytes per second, so the controller bus saturates before the individual 6 Gbps per-port rating or the 30 AWG conductors become a bottleneck.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.