We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in

XTAR Starlink V3 Cable Cat6 75FT 22.9M network ethernet cable

SKU CH-CRFV-B9CCN

A 75-foot CAT6 ethernet cable with waterproof Starlink V3 connectors rated for 2000 Mbps data transfer

  • TypeStarlink V3 Cable
  • Cat6
  • Connector AStarlink V3
  • Features, , , ,
  • Designed for Starlink Gen 3 with 75FT length for flexible placement
  • Waterproof and snow-resistant cover ensures reliable outdoor connectivity
  • CAT6 26AWG copper cable supports up to 2000Mbps data transfer
  • Simple plug-and-play setup requires no configuration
  • Metal shielding and sturdy PVC jacket provide stable indoor and outdoor performance

Starlink Gen 3 Replacement Cable

This 75FT Cat6 ethernet cable is built specifically for the Starlink Rectangular Satellite V3. It carries both data and power between the dish and the router in a single run. The 26AWG solid copper conductors are metal-shielded and wrapped in a UV-resistant PVC jacket rated for permanent outdoor exposure. Installers who need a longer reach than the factory lead will find the 22.9 metre length practical for roof or pole mounting.

All-Weather Outdoor Performance

The waterproof and snow-resistant protective cover keeps the connection stable through rain, ice and direct sunlight. Cat6 specification supports data transfer up to 2000Mbps, so the link will not bottleneck the satellite service. The shielded single-core construction rejects interference from nearby power lines or RF equipment. No active electronics are in the cable, so power draw is limited to the dish and router themselves.

Plug-and-Play Build Integration

Both ends terminate in the proprietary Starlink V3 connector for direct mating with the Gen 3 dish and router — no adapters or crimping required. The sturdy jacket resists abrasion when routed through conduit, along eaves or across a yard. Builders who need a shorter run should note that this SKU is fixed at 75FT; the same series is offered in 10FT and 30FT lengths for tighter installs.

Highlights

  • Designed for Starlink Gen 3 with 75FT length for flexible placement
  • Waterproof and snow-resistant cover ensures reliable outdoor connectivity
  • CAT6 26AWG copper cable supports up to 2000Mbps data transfer
  • Simple plug-and-play setup requires no configuration
  • Metal shielding and sturdy PVC jacket provide stable indoor and outdoor performance

Specifications

BrandXTAR
ModelStarlink V3 Cable
TypeStarlink V3 Cable
Cat6
Connector AStarlink V3
Features, , , ,

Questions about this item

How do I install the 75FT Starlink V3 cable and what step is often missed?

Route the cable from the Starlink Gen 3 dish to the router, then press each Starlink V3 connector firmly until it clicks; the step often missed is not seating the connector fully, which breaks the waterproof seal and can cause signal loss.

What maintenance or replacement will the 22.9M Cat6 26AWG cable need over time?

Inspect the PVC jacket and metal-shielded layer annually for UV cracking or abrasion, especially at bends near the dish mount; replace the cable if the shield is exposed or the Starlink V3 connector latch no longer locks.

What limit appears first on the 2000Mbps Cat6 link during sustained heavy use?

The 26AWG single-core copper conductors reach their thermal and voltage-drop limit on a 75FT run before the Cat6 2000Mbps rating does, so sustained maximum throughput may throttle if the cable is coiled tightly or in high ambient heat.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.