We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black shielded Cat6A patch cable, 75 ft, non-booted RJ45 connectors, flat matte jacket

SANOXY

SANOXY Cat6A Shielded Ethernet Cable 75FT 10Gbps 500MHz 26AWG Black

SKU CH-4T08-VVFVP

Shielded Cat6A patch cable carries 10 Gbps over 75 ft with 500 MHz bandwidth, pure copper 26 AWG conductors and gold-plated RJ45 connectors

Length 75 ft.

Show 3 more configurations
  • 10 Gbps speed and 500 MHz bandwidth for high-performance networking
  • Shielded STP design reduces electromagnetic interference and crosstalk
  • Pure bare copper 26 AWG conductors ensure minimal signal loss
  • 50-micron gold-plated RJ45 contacts resist corrosion for stable connections
  • Non-booted connector saves space in high-density patch panels and switches

Compact 75FT Cat6A for dense racks

This 75-foot Cat6A patch cord is built for short runs between patch panels, switches and side-by-side devices where space is tight. The non-booted RJ45 connectors sit flush, so adjacent ports stay accessible in high-density cabinets. Pure bare copper conductors keep resistance low over the full length.

Shielded STP holds 10Gbps under load

The STP shielding suppresses electromagnetic interference and crosstalk when many cables run in parallel trays or near power supplies. At 500 MHz bandwidth the link sustains 10 Gbps throughput during continuous streaming, gaming or cloud workloads without the error spikes seen on unshielded runs. Gold-plated contacts resist oxidation that would otherwise degrade long-term signal quality.

Non-booted plugs simplify tight installs

Without a strain-relief boot the connector slips into crowded patch panels and switches with a single push, reducing install time in cabinet rows. The 26 AWG stranded copper bends easily around cable managers but can kink if pulled sharply around sharp corners. Verify the latch clicks fully; a partial seat is the most common cause of intermittent link drops.

Highlights

  • 10 Gbps speed and 500 MHz bandwidth for high-performance networking
  • Shielded STP design reduces electromagnetic interference and crosstalk
  • Pure bare copper 26 AWG conductors ensure minimal signal loss
  • 50-micron gold-plated RJ45 contacts resist corrosion for stable connections
  • Non-booted connector saves space in high-density patch panels and switches

Specifications

No published specifications for this item yet.

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

Does the 26AWG pure copper conductor generate noticeable heat when carrying 10Gbps traffic all day?

The 26AWG pure bare copper conductors are sized for low resistance at 10Gbps, so heat build-up during continuous operation is negligible.

What RJ45 port type must my switch or patch panel already have to use the non-booted connectors on this cable?

Standard RJ45 ports accept the non-booted plugs; the short bootless design simply eases insertion in high-density panels.

Will the 500MHz shielded STP cable work reliably alongside older Cat5e patch cords in the same bundle?

Yes, the shielded STP construction with 500MHz bandwidth prevents crosstalk, so it coexists cleanly with legacy Cat5e cables in shared pathways.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.