We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Short blue shielded Cat6A cable with non-booted gold RJ45 connectors

SANOXY

SANOXY Cat6A network ethernet cable 3FT Blue 10Gbps 500MHz 26AWG 50-micron gold RJ45 non-booted STP

SKU CH-D9ZS-1CYZS

A shielded Cat6A patch cable with 26AWG pure copper conductors and 50-micron gold RJ45 contacts, supporting 10Gbps at 500MHz for short, high-density connections

Length 3 ft.

Show 3 more configurations
  • 10 Gbps speed and 500 MHz bandwidth for high-performance networking
  • Shielded STP construction reduces electromagnetic interference and crosstalk
  • 26 AWG pure bare copper conductors ensure excellent conductivity and minimal signal loss
  • Non-booted RJ45 connectors save space in high-density network environments
  • 50-micron gold-plated contacts provide corrosion resistance and stable long-term performance

Ideal for tight patch-panel runs

This 3 ft Cat6A patch cord is built for short, high-density connections between switches, patch panels or side-by-side equipment. Shielded STP construction and 26 AWG pure copper conductors deliver 10 Gbps throughput at 500 MHz bandwidth. The non-booted RJ45 plugs with 50-micron gold contacts save space and resist corrosion in crowded racks.

Replaces longer unshielded cords

Swap out standard Cat5e or unshielded Cat6 cables when electromagnetic interference degrades signal integrity in dense cabinets. The upgrade is justified where crosstalk or EMI from adjacent hardware causes packet loss or speed negotiation failures. Shielding and higher bandwidth headroom keep 10 Gbps links stable without re-terminating existing infrastructure.

Tool-free press-fit installation

Push the non-booted connectors directly into keystone jacks or switch ports; no crimping or boot removal is required. The slim profile eases routing through packed cable managers. The only common issue is accidental unplugging if the latch tab catches on neighbouring cables — route with a slight service loop to prevent tension on the plug.

Highlights

  • 10 Gbps speed and 500 MHz bandwidth for high-performance networking
  • Shielded STP construction reduces electromagnetic interference and crosstalk
  • 26 AWG pure bare copper conductors ensure excellent conductivity and minimal signal loss
  • Non-booted RJ45 connectors save space in high-density network environments
  • 50-micron gold-plated contacts provide corrosion resistance and stable long-term performance

Specifications

No published specifications for this item yet.

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

What clearance is needed for the non-booted RJ45 connectors?

The non-booted RJ45 connectors fit tight patch panels and switch ports without extra boot space, ideal for high-density racks where cables sit side by side.

How do I terminate or seat the shielded STP cable correctly?

Push each RJ45 plug until it clicks; the shielded design requires full insertion so the drain wire contacts the jack ground, otherwise EMI protection is lost.

Will the 50-micron gold-plated contacts need re-termination over time?

The 50-micron gold plating resists corrosion on the 26AWG pure copper conductors, so the connectors maintain stable contact without re-termination for the cable's service life.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.