We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black Y-splitter power cord with C14 male plug branching to C13 and NEMA 5-15R female connectors, 20ft length

DIXSG

DIXSG EJ-6005 C14 to C13 + NEMA 5-15R Y Splitter 20ft

SKU CH-0VFS-AWTHV

A 20‑foot Y‑splitter cable connects a single C14 inlet to both a C13 and a NEMA 5‑15R outlet, rated 10 A at 250 V with 0.75 mm² copper conductors

  • Length20 feet
  • Connector DetailFemale-to-Male
  • SpecificationsVoltage: 250 volts; Current: 10 amps; Connector: Female-to-M
  • Powers monitor and adapter from one C14 inlet using C13 plus NEMA 5-15R outputs
  • 20-foot length reaches distant PDUs or power strips without extra extensions
  • 10-amp 250-volt rating supports standard server and peripheral loads safely
  • 75 mm² pure copper conductors reduce resistance and heat during operation
  • Thick PVC jacket resists abrasion and meets flame-retardant requirements

C14 to C13 plus NEMA 5-15R Y splitter

This 20 foot cord splits a single IEC 320 C14 inlet into a C13 outlet and a NEMA 5-15R outlet. It lets you power a monitor and a second device from one PDU or UPS port. The Y layout reduces cable count behind racks or desks. Builders who need more than two branches cannot use this cord.

10 amp rating with 0.75 mm² copper conductors

Three 0.75 mm² pure copper cores carry up to 10 amps at 250 volts with low resistance and low heating under continuous load. The thickened PVC jacket resists abrasion, heat and flame. Installations that require a higher current rating or a different wire gauge cannot use this cord.

IEC 320 C14 input limited to 10 amps total

The single C14 male plug feeds both outputs, so combined draw must stay within the 10 amp limit. The cord is not UL listed. Environments that mandate a listed assembly or a higher combined load cannot use this cord.

Highlights

  • Powers monitor and adapter from one C14 inlet using C13 plus NEMA 5-15R outputs
  • 20-foot length reaches distant PDUs or power strips without extra extensions
  • 10-amp 250-volt rating supports standard server and peripheral loads safely
  • 75 mm² pure copper conductors reduce resistance and heat during operation
  • Thick PVC jacket resists abrasion and meets flame-retardant requirements

Specifications

BrandDIXSG
ModelEJ-6005
Length20 feet
Connector DetailFemale-to-Male
SpecificationsVoltage: 250 volts; Current: 10 amps; Connector: Female-to-Male; UL Listed: false

Questions about this item

Does the 20-foot Y-splitter cord run warm when both the C13 and the 5-15R outlets are drawing a full 10 amps?

The cord uses three 0.75 mm² pure copper conductors designed for low resistance and low heating, so it stays cool even under continuous 10-amp load.

What must my power source provide for this splitter to work?

You need a single IEC 320 C14 inlet supplying up to 250 volts at 10 amps.

Can I plug the C13 leg into an older server supply while the 5-15R leg feeds a legacy monitor?

Yes, the splitter is compatible with computers, servers, monitors and other peripherals that accept standard C13 or NEMA 5-15R connections.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.