We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black square 80 mm case fan with Maglev bearing and two-wire connector

Zyvpee

Zyvpee ME80251V3-000C-A99 80 mm case fan

SKU CH-VYJF-AYWEK

80 mm Maglev case fan delivering 30-35 CFM at 2500-2999 RPM with 25-30 dBA noise

  • TypeCase Fan
  • CompatibilityCase
  • Bearing TypeMaglev
  • RPM2500-2999 RPM
  • Air Flow30-35 CFM
  • Noise Level25 - 30 dBA
  • Maglev bearing reduces friction for quiet 25-30 dBA operation
  • 30-35 CFM airflow moves heat through tight 80 mm spaces
  • DC 12 V 1.1 W draw keeps power load low
  • 2-wire 2-pin connector fits standard case headers
  • 2500-2999 RPM range balances cooling and acoustics

Zyvpee 80 mm Maglev case fan

The Zyvpee ME80251V3-000C-A99 is an 80 mm case fan built around a Maglev bearing for reduced friction. It runs on 12 V DC and draws 1.1 W through a two-wire, two-pin connector. The frame measures 80 by 80 by 25 mm and is finished in black with no LED lighting. Airflow ranges from 30 to 35 CFM at 2500 to 2999 RPM.

Suited for tight chassis spots needing steady

This fan fits small-form-factor cases, NAS enclosures or GPU brackets that only accept 80 mm mounts and where a two-pin header is available. Builders who require PWM speed control, RGB illumination or higher static pressure for dense radiators should look elsewhere because the unit lacks a fourth wire, any lighting and is rated at 25 to 30 dBA.

Drops into any 80 mm mounting grid

The square 80 mm footprint aligns with standard case, radiator or drive-cage holes while the Maglev bearing keeps long-term noise consistent. Two-pin power means the motherboard or fan controller can only vary voltage for speed changes, freeing a four-pin header for a CPU cooler. The slim 25 mm depth clears most side-panel windows and cable-routing channels.

Highlights

  • Maglev bearing reduces friction for quiet 25-30 dBA operation
  • 30-35 CFM airflow moves heat through tight 80 mm spaces
  • DC 12 V 1.1 W draw keeps power load low
  • 2-wire 2-pin connector fits standard case headers
  • 2500-2999 RPM range balances cooling and acoustics

Specifications

SeriesME80251V3-000C-A99
ModelME80251V3-000C-A99
TypeCase Fan
CompatibilityCase
Bearing TypeMaglev
RPM2500-2999 RPM
Air Flow30-35 CFM
Noise Level25 - 30 dBA
Power Connector2 wires
ColorBlack
LEDNon-LED
FeaturesDC square Cooler
Dimensions80*80*25mm

Questions about this item

What motherboard header does the 2-wire connector fit?

The fan uses a 2-wire, 2-pin connector that plugs into a standard 12 V DC fan header on the motherboard or a compatible fan controller.

Can the Maglev bearing and 2500-2999 RPM range work with an older 3-pin or 4-pin header?

Yes, the 2-pin plug fits the first two pins of a 3-pin or 4-pin header; the fan will run at full 12 V speed since there is no PWM or tachometer wire.

How can I confirm the fan is moving the rated 30-35 CFM at 25-30 dBA after installation?

Listen for a quiet 25-30 dBA hum and feel steady airflow at the case vent; the Maglev bearing should run without rattling at 2500-2999 RPM.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.