We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small black 30mm square case fan 30mm thick 2-pin connector no LED

Zyvpee

Zyvpee DFS301012M 30mm 12V 1.3W 2-Pin Case Fan

SKU CH-9VM2-AWKZ2

30 mm ball-bearing case fan runs on 12 V at 1.3 W with a 2-pin connector

  • TypeCase Fan
  • Fan Size30mm
  • Bearing TypeBall
  • Power Connector2 Pin
  • ColorBlack
  • LEDNon-LED
  • Compact 30 mm frame fits tight chassis spaces
  • Ball bearing ensures durable long-life operation
  • 12 V 1.3 W draw keeps power use low
  • Two-pin connector simplifies installation
  • Suits set-top boxes routers and hard-disk enclosures

Compact 30 mm case fan

The Zyvpee DFS301012M is a 30 mm square frame fan designed for tight enclosures such as set-top boxes, routers and hard-disk housings. It runs on 12 V and draws 1.3 W through a simple two-pin power connector. The ball-bearing motor and black non-LED housing keep the profile low at 30 by 10 mm. This fan suits builders who need targeted airflow in confined spaces.

Replacing louder sleeve-bearing units

The two-pin layout drops straight into legacy headers that lack PWM control, making the swap straightforward on older boards or embedded gear. Ball bearings reduce the rattle that develops in sleeve designs after extended heat cycles, so the upgrade is worth it when acoustic consistency matters more than variable speed. Buyers who need software fan curves or a three- or four-pin header will not find that control here.

Fits 30 mm mounting holes

The 30 mm hole pattern aligns with standard 3010 cut-outs, so no adapter brackets are required. Two wires keep cable routing simple in cramped chassis, and the 1.3 W draw leaves ample headroom on a shared 12 V rail. Because the unit has no integrated lighting or speed signal, it frees up header space for other monitored fans. Ensure the host device supplies a constant 12 V source, as no voltage regulator is onboard.

Highlights

  • Compact 30 mm frame fits tight chassis spaces
  • Ball bearing ensures durable long-life operation
  • 12 V 1.3 W draw keeps power use low
  • Two-pin connector simplifies installation
  • Suits set-top boxes routers and hard-disk enclosures

Specifications

Brand3ccooler.com
SeriesDFS301012M
ModelDFS301012M
TypeCase Fan
Fan Size30mm
Bearing TypeBall
Power Connector2 Pin
ColorBlack
LEDNon-LED
Dimensions30*10mm

Questions about this item

Will this 30mm fan fit a 3010 mounting pattern?

Yes, the fan measures 30 by 10mm and matches the standard 3010 mounting holes used on set-top boxes, routers and hard-disk enclosures.

How do I connect the 2-pin plug, and what mistake should I avoid?

Plug the two wires onto a 12V DC header matching the polarity marked on the fan; the common error is reversing the positive and negative leads, which prevents the fan from spinning.

When will the ball bearing need replacement?

The ball bearing is rated for long life in continuous 12V operation; expect to replace the fan only if noise increases or airflow drops after extended use.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.