We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Small black 60 by 25 millimetre blower fan with three pins

Zyvpee

Zyvpee D06F-12B1S1 07B 60x25mm 12V .33A 3-pin blower

SKU CH-NEJT-PYF5K

A 60 by 25 mm DC blower fan with a mixed ball-and-sleeve bearing runs on 12 V and .33 A through a 3-pin connector

  • TypeCase Fan
  • CompatibilityCPU Cooler
  • Bearing Type1 Ball, 1 Sleeve
  • Power Connector3 Pin
  • ColorBlack
  • LEDNon-LED
  • Compact 60×25 mm blower fits tight CPU coolers
  • 12 V DC motor draws only 0.33 A
  • Mixed ball-and-sleeve bearing balances silence and life
  • Standard 3-pin connector works with most motherboards
  • Non-LED black frame keeps builds clean and professional

Zyvpee D06F-12B1S1 07B Blower Fan

The Zyvpee D06F-12B1S1 07B is a 12V DC blower designed for compact CPU coolers and projector housings. Its 60 by 25mm frame fits tight ducting where axial fans cannot direct airflow effectively. Builders maintaining small-form-factor systems or replacing original projector cooling modules will find the form factor matches the original specification.

Capacity and Headroom

The fan draws 0.33A at 12V, delivering focused static pressure through a narrow outlet. It handles targeted component cooling in restricted spaces but runs out of volume when asked to ventilate an entire chassis. The mixed ball-and-sleeve bearing supports continuous operation at the rated voltage without extra headroom for over-volting.

Three-Pin Power Interface

A standard three-pin connector supplies power and a tachometer signal for speed monitoring. Voltage control is the only regulation method; PWM headers will run the blower at full speed unless the motherboard supports DC-mode switching. The lack of a fourth pin means no duty-cycle control, so low-speed quiet operation depends entirely on the board’s voltage-range capability.

Highlights

  • Compact 60×25 mm blower fits tight CPU coolers
  • 12 V DC motor draws only 0.33 A
  • Mixed ball-and-sleeve bearing balances silence and life
  • Standard 3-pin connector works with most motherboards
  • Non-LED black frame keeps builds clean and professional

Specifications

SeriesD06F-12B1S1
ModelD06F-12B1S1
TypeCase Fan
CompatibilityCPU Cooler
Bearing Type1 Ball, 1 Sleeve
Power Connector3 Pin
ColorBlack
LEDNon-LED
FeaturesDC Blower

Questions about this item

Will the 60 mm blower fit the mounting holes on my older CPU cooler that uses 60 mm fans?

The fan measures 60 mm square by 25 mm thick, matching the standard 60 mm mounting pattern used on many legacy CPU coolers.

How can I confirm the blower is running correctly once installed?

Connect the 3-pin connector to a 12 V header; the fan should spin and draw approximately .33 A, which you can verify in BIOS or monitoring software.

Does the package include mounting screws or a 3-pin to 4-pin adapter?

The box contains only the blower unit itself; screws and any adapter cables must be purchased separately.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.