We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 150mm PCIe 3.0 x16 right-angled riser cable with narrow EMI-shielded ribbon

Wilfly

Wilfly PCIE16NR15 150mm PCI-E 3.0 x16 Right Angled Riser Cable

SKU CH-0XTX-96XQD

A 150 mm PCI-E 3.0 x16 right-angled riser cable with EMI shielding and a narrow design for vertical GPU mounting in compact chassis

  • TypeInternal Power Cables
  • ColorBlack
  • Cable Length5.90in/150mm
  • Connector A1 x PCI Express 3.0 x16 female 90-Degree Right Angled (to Ad
  • Connector B1 x PCI Express 3.0 x16 male (to M/B PCIe Slot)
  • Connector Number2
  • Right-angled connector fits tight chassis spaces
  • 150 mm flexible EMI-shielded cable keeps signal clean
  • PCIe 3.0 x16 female to male carries full bandwidth
  • Narrow profile enables vertical GPU mounting in 1-2U cases
  • Rigid PCB with standoffs secures card without sag

150mm PCIe 3.0 x16 Riser Cable

This 150mm flexible extender connects a graphics card to a motherboard slot using a 90-degree right-angled female connector. EMI shielding protects signal integrity across the full x16 width. The narrow profile fits tight chassis where a straight plug would foul adjacent components. It is built for vertical GPU mounting in 1U to 2U cases or compact gaming builds.

PCIe 3.0 x16 bandwidth ceiling

The cable carries the PCI Express 3.0 x16 electrical interface, so maximum throughput is limited to the 3.0 specification. Signal quality depends on the 150mm trace length and shielding; longer runs would increase latency and error risk. No active re-drivers are present, so the link relies entirely on the host and device equalisation. Systems requiring PCIe 4.0 or 5.0 speeds cannot use this cable at those rates.

Fits x16 cards in space-constrained slots

The right-angle connector and slim PCB allow full-length graphics cards to sit parallel to the motherboard, clearing low-profile heatsinks or drive cages. Bandwidth headroom is sufficient for current x16 GPUs operating at Gen 3 speeds. Builds that need Gen 4 or Gen 5 signalling, or cables longer than 150mm, will not be served by this model.

Highlights

  • Right-angled connector fits tight chassis spaces
  • 150 mm flexible EMI-shielded cable keeps signal clean
  • PCIe 3.0 x16 female to male carries full bandwidth
  • Narrow profile enables vertical GPU mounting in 1-2U cases
  • Rigid PCB with standoffs secures card without sag

Specifications

TypeInternal Power Cables
ColorBlack
Cable Length5.90in/150mm
Connector A1 x PCI Express 3.0 x16 female 90-Degree Right Angled (to Add-in PCIe Card)
Connector B1 x PCI Express 3.0 x16 male (to M/B PCIe Slot)
Connector Number2

Questions about this item

How do I know if the 150 mm right-angled cable will reach my motherboard slot?

Measure the straight-line distance from your motherboard's PCIe x16 slot to where the graphics card will sit; the cable is 150 mm (5.90 in) long and has a 90-degree female connector that points the card parallel to the board.

Will my GPU run at full PCIe 3.0 x16 speed through this extender?

The cable is specified for PCIe 3.0 x16 and uses EMI shielding to minimise signal loss, so a compatible GPU should operate at the full 3.0 x16 link width in practice.

Does the PCIe 3.0 x16 interface limit bandwidth compared to newer standards?

PCIe 3.0 x16 caps the link at 16 GT/s per lane, which is the maximum this cable supports; newer GPUs will fall back to this speed when installed.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.