We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Four black braided fan splitter cables each 10.5 inches long with one 4-pin motherboard connector splitting to three 3-pin

Vszerda

Vszerda PWM Fan Splitter 4 Pin 1 to 4 10.5in 4 Pack

SKU CH-24GF-5WGRZ MPN 1007

A 10.5-inch PWM splitter connects four case fans to one motherboard header using braided 24 AWG tinned-copper cable rated to 80 °C

  • Connect four fans to one header with 4-pin PWM and three 3-pin connectors
  • Braided black sleeving protects 1007 24 awg tinned-copper wires from dust and breakage
  • PVC insulation rated to 80 °C keeps 1.4 mm conductors safe under load
  • Each 10.5 inch cable lets you route fans freely inside the case
  • Pack of four splitters powers multiple cooling zones from a single motherboard port

Four-way PWM fan splitter

The Vszerda PWM fan splitter is a 4-pin Y-cable that lets four case fans share a single motherboard header. One end carries a 4-pin female connector and the other splits into three 3-pin and one 4-pin connectors. Each cable measures 10.5 inches and uses 24 AWG tinned-copper wire with PVC insulation. The pack contains four identical splitters.

Braided sleeving and flexible routing

The cables are strongly braided and sleeved to resist dust and breakage while remaining flexible enough to route around internal components. Rated to 80 °C, the 1.4 mm OD conductors use an 11-strand 0.12 mm construction for reliable current delivery. PWM signalling passes through the 4-pin path so the motherboard can control fan speed on the connected 4-pin fan.

Builders expanding fan counts on limited headers

This splitter suits builders who need to run more fans than the board provides headers for and who accept that only one fan reports speed to the BIOS. It does not suit systems that require individual speed monitoring for every fan or setups where total fan current exceeds the header rating.

Highlights

  • Connect four fans to one header with 4-pin PWM and three 3-pin connectors
  • Braided black sleeving protects 1007 24 awg tinned-copper wires from dust and breakage
  • PVC insulation rated to 80 °C keeps 1.4 mm conductors safe under load
  • Each 10.5 inch cable lets you route fans freely inside the case
  • Pack of four splitters powers multiple cooling zones from a single motherboard port

Specifications

No published specifications for this item yet.

Questions about this item

How long is each cable so I can plan routing inside my case?

Each splitter measures 10.5 inches from the motherboard connector to the fan ends, giving enough reach for most mid-tower layouts.

What is the correct way to orient the 4-pin motherboard connector so the PWM signal works?

Align the keyed tab on the 4-pin female header with the notch on the motherboard fan header; forcing it backwards breaks the PWM control line.

Will the braided sleeving hold up if I need to reroute the cables after a few months?

The PVC-insulated 1007 24 AWG tinned-copper wires are wrapped in a tight braided sleeve rated to 80 °C, so repeated gentle rerouting will not fray the insulation.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.