Vszerda
Vszerda PCIe 4.0 x16 Riser Cable 180° 18cm
PCIe 4.0 x16 riser cable with 180-degree connectors and 18cm length for vertical GPU mounting
- TypePCIe
- Connector APcie
- Connector BPcie
- Connector DetailPCIe
- Terminal GenderMale-to-Female
- SpecificationsPUSOKEIb8g19oy4se-16, PCIe, PUSOKEI
- Supports 128 Gbps bandwidth with PCIe 4.0 x16 interface
- 180° reverse connector enables vertical GPU mounting in tight cases
- Shielded design reduces electromagnetic interference for stable signal transmission
- Flexible flat cable simplifies routing and improves airflow inside the chassis
- Backward compatible with PCIe 3.0, 2.0 and 1.0 devices
PCIe 4.0 x16 Riser Cable 180° 18cm
This Vszerda riser cable extends a PCIe 4.0 x16 graphics card away from the motherboard using a 180-degree dual-sided connector. The 18cm flat cable supports 128Gbps bandwidth and remains backward compatible with PCIe 3.0, 2.0 and 1.0. It is built from ABS and shielded for high-speed signal integrity. Plug-and-play installation requires no drivers.
Builders mounting GPUs vertically
The cable suits builders who need to position a graphics card vertically or in a custom loop layout where the motherboard slot cannot be used directly. The 180-degree reverse ports and flexible flat design simplify routing in tight cases. Buyers who need a longer reach than 18cm or a different connector angle should look at other options.
180-degree dual-sided PCIe connector
The defining specification is the 180-degree reverse connector orientation on both ends, which determines whether the card can be mounted in the intended direction. The cable carries PCIe 4.0 x16 signalling at 128Gbps and fits RX 7000 series and 4000 series GPUs. Verify that 18cm length and the connector gender match the build before purchase.
Highlights
- Supports 128 Gbps bandwidth with PCIe 4.0 x16 interface
- 180° reverse connector enables vertical GPU mounting in tight cases
- Shielded design reduces electromagnetic interference for stable signal transmission
- Flexible flat cable simplifies routing and improves airflow inside the chassis
- Backward compatible with PCIe 3.0, 2.0 and 1.0 devices
Specifications
| Brand | PUSOKEI |
|---|---|
| Model | PUSOKEIb8g19oy4se-16 |
| Type | PCIe |
| Connector A | Pcie |
| Connector B | Pcie |
| Connector Detail | PCIe |
| Terminal Gender | Male-to-Female |
| Specifications | PUSOKEIb8g19oy4se-16, PCIe, PUSOKEI |
| Shielding | High Speed |
| Construction | Acrylonitrile Butadiene Styrene (ABS) |
| Features | PCIe, PUSOKEI, PUSOKEIb8g19oy4se-16 |
| Disclaimer | CE |
Questions about this item
Does this riser cable need a separate power connector to run a GPU?
No, the 18 cm PCIe 4.0 x16 cable carries power through the slot itself; just plug the male end into the motherboard and the female end into the card.
Will the 180-degree connector clear a PCIe 3.0 motherboard slot if I keep my older board?
Yes, the riser is backward compatible with PCIe 3.0, 2.0 and 1.0 slots, so it fits the same physical x16 connector on an older board.
How can I confirm the link is actually running at PCIe 4.0 x16 after I install it?
Check the link width and speed in GPU-Z or your motherboard BIOS; both should report x16 and 4.0 when the GPU is under load.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
WAWEIS
WAWEIS power adapter for AmazonBasics SB210 2.1 Channel Bluetooth Sound Bar
$15.99
0.00018432BTC
In stock
