We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black OCuLink active cable with SFF-8611 4i and SFF-8643 connectors, 50 cm

Vszerda

Vszerda OCuLink SFF-8611 4i to SFF-8643 active cable 50cm

SKU CH-MJCN-S3PP2

Active OCuLink cable bridges SFF-8611 and SFF-8643 connectors at up to 8 Gbps over 50 cm

  • TypeOculink
  • ColorBlack
  • SpecificationsOculink
  • ShieldingHigh Speed 64Gbps
  • FeaturesHigh Speed 64Gbps
  • Connect internal backplane to OCuLink controller with SFF-8611 to SFF-8643 active cable
  • Secure active latch prevents accidental disconnect during data transfer
  • 50 cm length fits compact eGPU and SSD enclosures
  • 64 Gbps shielding supports high-speed PCIe 4.0 signals
  • Up to 8 Gbps transfer rate for external graphics and storage workloads

OCuLink SFF-8611 4i to SFF-8643 active cable

This 50 cm active cable bridges an OCuLink SFF-8611 4i controller to a backplane or enclosure with an SFF-8643 connector. It targets builders adding external GPU or SSD links where a native OCuLink port is available. The cable is not compatible with SFF-8643 slimline SAS RAID cards.

Active latch and PCIe 4.0 signalling

The active latch secures each end without thumb screws, so installation is a simple push until it clicks. Route the 50 cm length carefully; sharp bends near the connector housings can stress the active circuitry and cause link errors. A free OCuLink interface on the host side is the only system requirement.

64 Gbps shielding with 8 Gbps lane rate

Each of the four lanes runs at up to 8 Gbps under PCIe 4.0, giving aggregate bandwidth suited to modern GPUs and high-speed SSDs. The 64 Gbps shielding rating provides headroom for signal integrity at full speed. Runs longer than 50 cm or passive alternatives would be needed for greater reach.

Highlights

  • Connect internal backplane to OCuLink controller with SFF-8611 to SFF-8643 active cable
  • Secure active latch prevents accidental disconnect during data transfer
  • 50 cm length fits compact eGPU and SSD enclosures
  • 64 Gbps shielding supports high-speed PCIe 4.0 signals
  • Up to 8 Gbps transfer rate for external graphics and storage workloads

Specifications

BrandNGFF
TypeOculink
ColorBlack
SpecificationsOculink
ShieldingHigh Speed 64Gbps
FeaturesHigh Speed 64Gbps

Questions about this item

How do I confirm the active cable is functioning after connecting an SFF-8611 controller to an SFF-8643 backplane?

Verify the active latch clicks securely into both connectors and check that the host system detects the attached drives or eGPU at the expected PCIe 4.0 link speed.

What does the package contain and what extra parts are needed for a typical eGPU or SSD setup?

The box includes the 50 cm active cable with SFF-8611 4i and SFF-8643 male ends; you must supply a controller with a free OCuLink SFF-8611 port and a backplane or device with an SFF-8643 connector.

Which version should I choose if my controller uses an SFF-8611 4i port and my backplane uses SFF-8643?

Select this SFF-8611 4i to SFF-8643 active cable; it is built for PCIe 4.0 links up to 64 Gbps and will not work with SFF-8643 SAS RAID cards.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.