We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Vszerda Mini SAS SFF-8087 cable, 1 metre, 30 AWG, 36-pin locking connectors both ends

Vszerda

Vszerda Mini SAS SFF-8087 Cable 6.0 Gbps 1M 3.3Ft 30 AWG 36-pin

SKU CH-HVPJ-PAZ8M

Connects SAS devices with a 36-pin SFF-8087 male Mini-SAS plug on each end, supporting 6.0 Gbps over a 1-metre length using 30 AWG wires

  • Internal 6.0 Gbps SAS link for server and RAID arrays
  • 1 metre length fits standard rack and workstation chassis
  • 30 AWG conductors keep signal integrity over the run
  • 36-pin SFF-8087 locking plugs on both ends secure the connection
  • Designed for internal Mini SAS SFF-8087 to SFF-8087 cabling

Internal SAS Link for Workstations and Servers

This Mini SAS SFF-8087 cable connects RAID controllers, backplanes or host-bus adapters inside workstations, servers and rack-mounted systems. Each end carries a 36-pin male plug with a locking latch so the link stays seated during vibration or chassis movement. The 1 metre length suits typical internal routing without excess slack.

Sustained 6.0 Gbps Throughput

Rated for 6.0 Gbps per lane, the cable maintains that bandwidth across the full 1 metre run rather than only in short bursts. The 30 AWG conductors keep signal loss low enough for continuous RAID rebuilds, parity checks or bulk data migrations without throttling. Shielding and the latch design reduce intermittent errors that can appear when lesser cables heat up under load.

30 AWG Build with Locking Latches

The 30 AWG wire gauge balances flexibility for tight routing with the mechanical strength needed for repeated insertion cycles. Both SFF-8087 connectors feature a positive locking latch that clicks audibly, preventing accidental disconnection during drive-swap operations or chassis maintenance. The assembly is supplied as a single 1 metre unit ready for internal deployment.

Highlights

  • Internal 6.0 Gbps SAS link for server and RAID arrays
  • 1 metre length fits standard rack and workstation chassis
  • 30 AWG conductors keep signal integrity over the run
  • 36-pin SFF-8087 locking plugs on both ends secure the connection
  • Designed for internal Mini SAS SFF-8087 to SFF-8087 cabling

Specifications

No published specifications for this item yet.

Questions about this item

Does the 30 AWG cable add noticeable heat or power draw when run continuously in a server?

The 30 AWG conductors carry the 6.0 Gbps SAS signal without active components, so the cable itself does not generate measurable heat or increase power consumption during all-day operation.

What port type must my RAID controller or backplane provide for this SFF-8087 cable to plug in directly?

Each end terminates in a 36-pin SFF-8087 male Mini-SAS plug with a locking latch, so the host and target devices must each present a matching SFF-8087 receptacle.

Will the 1 metre length and 6.0 Gbps rating work reliably with older 3 Gbps SAS drives still installed in the chassis?

Yes — the 6.0 Gbps cable is backward compatible with 3 Gbps SAS devices, and the 1 metre / 3.3 ft length stays well within the electrical limits for both speeds.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

More in SCSI / SAS / InfiniBand Cables

Similar items

Same shelf, same checkout — eight coins and a 30-minute rate lock.