We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 50cm cable with 38-pin MCIO male connector to SFF-8611 Oculink 4X plug

Vszerda

Vszerda MCIO 38Pin Male to SFF-8611 Oculink 4X Extender Cable 50cm

SKU CH-YE6V-JN8JV

Connects 38-pin MCIO to SFF-8611 Oculink 4X for 24 Gbps SSD and eGPU links over 50 cm

  • TypeOculink
  • ColorBlack
  • SpecificationsOculink
  • ShieldingHigh Speed 64Gbps
  • FeaturesHigh Speed 64Gbps
  • PCIe 5.0 support enables 64 Gbps bandwidth
  • 38-pin MCIO male to SFF-8611 Oculink 4X connector
  • 50 cm length suits eGPU and external SSD setups
  • Shielded design delivers 24 Gbps data transfer rate
  • SAS 3.0 and 4.0 compatibility for server and networking use

MCIO 38-Pin to Oculink 4X Extender Cable

This Vszerda cable connects an MCIO 38-pin male header to an SFF-8611 Oculink 4X receptacle over a 50cm run. It is built for PCIe 5.0 and SAS 3.0 or 4.0 signalling, enabling high-speed links between servers, storage arrays or eGPU enclosures and host boards.

For PCIe 5.0 and SAS 3.0

The cable suits builders who need a straight 50cm reach between those two connector types. It will not work for installations that require a different pin count, an alternative Oculink keying, a right-angle shell or a longer run.

24 Gbps rated throughput over MCIO 38-pin

The assembly is specified for up to 24 Gbps data transfer, matching PCIe 5.0 x4 and SAS 4.0 lane rates. Verify that both endpoints support this speed and the 38-pin MCIO / SFF-8611 pinout before purchasing.

Highlights

  • PCIe 5.0 support enables 64 Gbps bandwidth
  • 38-pin MCIO male to SFF-8611 Oculink 4X connector
  • 50 cm length suits eGPU and external SSD setups
  • Shielded design delivers 24 Gbps data transfer rate
  • SAS 3.0 and 4.0 compatibility for server and networking use

Specifications

BrandNGFF
TypeOculink
ColorBlack
SpecificationsOculink
ShieldingHigh Speed 64Gbps
FeaturesHigh Speed 64Gbps

Questions about this item

What clearance does the 38-pin MCIO male connector need to seat fully?

The 38-pin MCIO male connector is a low-profile card-edge design; allow a few millimetres of clearance beyond the board edge so the latch can engage without hitting adjacent components or a chassis wall.

Which end should be plugged in first to avoid bending the 50 cm cable?

Insert the SFF-8611 Oculink 4X end into the device port first, then route the 50 cm cable and seat the MCIO 38-pin male end into the board connector; reversing the order often forces a sharp bend at the MCIO side.

When should the cable be replaced if the 64 Gbps shielding degrades?

Replace the cable if intermittent link errors appear, the SFF-8611 latch no longer clicks securely, or the outer jacket shows cuts or kinks that could compromise the high-speed shielding.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.