We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Green circuit board with gold edge connector and screw hole

Vszerda

Vszerda M.2 SATA B/B+M Key to 2.5" SATA Adapter

SKU CH-JNAW-7X7GE

Converts SATA-based M.2 NGFF SSDs (B key, B+M key, 2230–2280 mm) to a 2.5" SATA 6.0 Gbps interface, but does not support PCIe NVMe M-key drives

  • Converts SATA-based M.2 NGFF SSDs into 2.5" SATA 6.0 Gbps drives
  • Supports B key and B+M key M.2 SSDs in 2230, 2242, 2260, 2280 lengths
  • Works with SATA revision I, II, III at 1.5, 3.0, 6.0 Gbps
  • Reduces power consumption using high-efficiency M.2 SSD
  • Does not support PCIe M key or M+B key NVME SSDs

Vszerda M.2 SATA Adapter for 2.5" Bays

This adapter converts a SATA-based M.2 NGFF SSD into a standard 2.5-inch SATA drive form factor. It is designed for users who want to install an M.2 SATA drive into a laptop or desktop bay that only accepts 2.5-inch drives. The card supports B key and B+M key M.2 modules in lengths from 2230 to 2280 millimetres. It does not work with PCIe-based NVME drives.

Sustained SATA III throughput up to 6.0 Gbps

The adapter maintains the full SATA III interface speed of 6.0 Gbps and is backward compatible with SATA revision I and II rates of 1.5 and 3.0 Gbps. Because it is a passive electrical conversion with no controller chip, sustained transfer rates depend entirely on the installed M.2 SATA SSD's own capabilities. There is no thermal throttling or protocol overhead introduced by the adapter itself.

Simple screw-mount installation with keying caution

Mount the M.2 SSD onto the PCB using the standoff and screw, then secure the assembly into a 2.5-inch drive bay or caddy. The most common issue is attempting to install an M key or M+B key NVME drive, which is physically incompatible and electrically unsupported. Verify the SSD uses a B key or B+M key SATA interface before purchase to avoid a mismatch.

Highlights

  • Converts SATA-based M.2 NGFF SSDs into 2.5" SATA 6.0 Gbps drives
  • Supports B key and B+M key M.2 SSDs in 2230, 2242, 2260, 2280 lengths
  • Works with SATA revision I, II, III at 1.5, 3.0, 6.0 Gbps
  • Reduces power consumption using high-efficiency M.2 SSD
  • Does not support PCIe M key or M+B key NVME SSDs

Specifications

No published specifications for this item yet.

Questions about this item

Does the adapter generate noticeable heat or draw extra power when an M.2 SATA SSD runs continuously?

The adapter is a passive board with no active components, so it adds no measurable heat or power draw beyond the SSD itself.

What host connector must my system provide for this adapter to work?

Your motherboard or enclosure needs a standard 2.5-inch SATA data and power connector.

Can I keep using my existing 2.5-inch SATA cables and drive bay with this adapter installed?

Yes, the adapter presents a regular 2.5-inch SATA interface, so your current cables and bay work without change.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.