We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black modular cable with four 8-pin connectors merging into a single angled 12VHPWR 16-pin plug

Vszerda

Vszerda ATX 3.0 PCIe 5.0 12VHPWR to Four 8-Pin Angled 90° Power Cable

SKU CH-5VV2-XYN2J

Converts four 8-pin PSU connectors into a single 12VHPWR 12+4-pin plug with 90° angled ends for tight GPU clearances, rated for 600 W and compatible with RTX 3090 Ti, 4070 Ti, 4080 and 4090 cards

  • Angled 90° connector fits tight GPU clearances
  • Converts four 8-pin PSU cables to one 12VHPWR plug
  • Supports up to 600W for RTX 3090 Ti 4070 Ti 4080 4090
  • PCIe 5.0 ATX 3.0 ready with 12+4 pin signal contacts
  • Single cable design reduces clutter and simplifies routing

Angled 12VHPWR Adapter

The Vszerda cable converts four 8-pin PCIe connectors into a single 12VHPWR plug for RTX 3090 Ti, 4070 Ti, 4080 and 4090 graphics cards. Its 90-degree upward angle eases routing in tight spaces around the GPU power socket. The assembly is rated for 600 W delivery under the ATX 3.0 and PCIe 5.0 specifications. Builders with older 12-pin RTX 3090 cards cannot use this adapter.

Thermal and Power Behaviour

The single-cable design reduces the number of individual wires running through the chassis, which can help airflow compared to multiple separate leads. All power passes through the 12VHPWR interface rated for 600 W, so the adapter itself adds no active cooling requirement. No fan noise or additional power draw is introduced beyond the GPU's normal consumption. The angled strain relief keeps the connector seated without sharp bends that could increase resistance.

Build Quality and Daily Use

The 90-degree moulded head clears low-profile side panels or bulky heatsinks that would block a straight connector. Four separate 8-pin plugs must be sourced from the power supply, so the PSU needs enough native PCIe outputs or modular ports. The cable bundle stays tidy because only one combined run reaches the graphics card. Compatibility is limited to 12+4-pin female GPU sockets; the older 12-pin Founders Edition design is explicitly not supported.

Highlights

  • Angled 90° connector fits tight GPU clearances
  • Converts four 8-pin PSU cables to one 12VHPWR plug
  • Supports up to 600W for RTX 3090 Ti 4070 Ti 4080 4090
  • PCIe 5.0 ATX 3.0 ready with 12+4 pin signal contacts
  • Single cable design reduces clutter and simplifies routing

Specifications

No published specifications for this item yet.

Questions about this item

How do I route the 90° angled 12VHPWR connector into a tight GPU cutout?

Insert the 12+4 pin plug straight into the card's female port; the right-angle bend points the four 8-pin tails toward the motherboard, clearing the side-panel window without forcing the latch.

Will the four 8-pin PSU connectors or the 12VHPWR socket wear out first after repeated reseats?

The 12VHPWR socket is rated for fewer insertion cycles than standard 8-pin headers, so the 16-pin end will reach its mechanical limit before the four 8-pin plugs.

At what sustained load does the 600 W rating become the limiting factor for an RTX 4090?

The cable is specified for 600 W continuous delivery; any workload that pushes the GPU past that draw — such as prolonged 4K gaming with power limit raised — will hit the cable's ceiling first.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.