We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Chrome wheel stud installer kit with threaded nuts and washers for Pontiac Pathfinder 1955-1958

V-Project Inc

V-Project Inc Wheel Stud Installer Kit Pontiac Pathfinder 1955-1958 M1/2x20 Half-20 Chrome

SKU CH-2HWT-7S0PH

Chrome M1/2×20 wheel-stud installer kit fits Pontiac Pathfinder 1955-1958 and other models

  • Colorchrome
  • Commercial/ResidentialResidential
  • Designed for Pontiac Pathfinder 1955-1958 fitment
  • M1/2 x 20 thread matches factory wheel studs
  • Pin-stud tool design speeds installation
  • Chrome finish resists corrosion during use
  • Compact 20 mm x 24.9 mm x 43.15 mm size fits tight hubs

Pontiac Pathfinder 1955-1958 fit

This installer kit is built for the Pontiac Pathfinder produced between 1955 and 1958. It supplies the hardware needed to fit pin-type wheel studs with an M1/2 x 20 thread. The components are finished in chrome for corrosion resistance. DIY owners and classic-car specialists can use the set for period-correct wheel maintenance.

20 mm x 24.9 mm x 43.15 mm dimensions

Each piece measures 20 mm by 24.9 mm by 43.15 mm, matching the original fastener envelope. The compact size lets the tool reach the hub without interfering with brake drums or backing plates. No power source is required, so the kit adds no electrical load to the vehicle. Operation stays quiet because only hand force is applied.

Chrome finish and pin-stud compatibility

The chrome coating protects the steel threads from rust during storage and after installation. The kit is shaped exclusively for pin studs, so it will not engage spline or press-in types. Buyers who need a different thread pitch or a spline-stud tool cannot use this set. No lubricant or torque adapter is included in the package.

Highlights

  • Designed for Pontiac Pathfinder 1955-1958 fitment
  • M1/2 x 20 thread matches factory wheel studs
  • Pin-stud tool design speeds installation
  • Chrome finish resists corrosion during use
  • Compact 20 mm x 24.9 mm x 43.15 mm size fits tight hubs

Specifications

Brandv-project
Colorchrome
Commercial/ResidentialResidential

Questions about this item

How do I install the wheel stud installer kit on a 1955-1958 Pontiac Pathfinder with M1/2x20 threads?

Thread the installer onto the M1/2x20 pin studs, then tighten the nut to press each stud into the hub. The step most people miss is verifying the 20 mm, 24.9 mm and 43.15 mm dimensions match the original stud length before pressing.

What maintenance or replacement will the chrome wheel stud installer kit need over time?

The chrome finish resists corrosion, but clean threads with a wire brush after each use and apply light oil to prevent galling. Replace the kit if the drive surfaces show rounding or the nut spins freely on the threads.

What limit appears first when using the M1/2x20 installer continuously on multiple wheels?

Heat buildup in the chrome-plated drive nut is the first limit; allow the tool to cool after every few studs to avoid thread damage and maintain the 0.787 inch by 0.980 inch by 1.698 inch tolerances.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.