We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in

UbiGear URJ45PT4 network connector 100 pcs CAT5e pass-through 8P8C gold-plated 24 AWG

SKU CH-YHZ8-ZW1S3 MPN URJ45PT4

A pack of one hundred CAT5e RJ45 pass-through connectors with gold-plated contacts for 24 AWG solid or stranded wire

  • TypeMale-to-Male
  • Changer TypeEthernet, Male-to-Male
  • Color100pcs;CAT5e
  • Wire GaugeEthernet
  • SpecificationsMale-to-Male, cat_5e, Ethernet, 100pcs;CAT5e, URJ45PT4
  • Dimensions6.604 cm x 7.112 cm x 13.716 cm
  • Pass-through design speeds up termination by letting wires feed through the connector
  • Gold-plated contacts on all pins resist corrosion and maintain signal integrity
  • Supports solid or stranded conductors up to 24 AWG with 1.02 mm maximum insulation diameter
  • 100 connectors per pack covers multiple cable runs and repair jobs
  • CAT5e rating meets IEEE specification for gigabit Ethernet data networking

100 CAT5e pass-through RJ45 connectors

This pack supplies one hundred UbiGear URJ45PT4 modular plugs for terminating Ethernet cable. Each connector is an 8P8C male-to-male type with gold-plated contacts. The pass-through design lets conductors exit the front so wiring order can be checked before crimping.

Installers terminating 24 AWG solid or stranded wire

Suited for technicians and hobbyists building or repairing Cat 5e patch cords with conductors up to 1.02 mm outer diameter. Not for cables using 23 AWG or thicker conductors unless the insulation is stripped first. Buyers needing shielded or Cat 6 rated plugs should choose a different product.

1.02 mm maximum conductor outer diameter

The single critical limit is the 1.02 mm (0.04 in) wire OD that the pass-through holes accept. Wire larger than this will not pass through the connector channels, making a proper termination impossible. Verify your cable dimensions before purchasing.

Highlights

  • Pass-through design speeds up termination by letting wires feed through the connector
  • Gold-plated contacts on all pins resist corrosion and maintain signal integrity
  • Supports solid or stranded conductors up to 24 AWG with 1.02 mm maximum insulation diameter
  • 100 connectors per pack covers multiple cable runs and repair jobs
  • CAT5e rating meets IEEE specification for gigabit Ethernet data networking

Specifications

BrandGE
ModelURJ45PT4
Part NumberURJ45PT4
TypeMale-to-Male
Changer TypeEthernet, Male-to-Male
Color100pcs;CAT5e
Wire GaugeEthernet
SpecificationsMale-to-Male, cat_5e, Ethernet, 100pcs;CAT5e, URJ45PT4
Dimensions6.604 cm x 7.112 cm x 13.716 cm
Package Quantity100 Count
Package Contents100 x Small
DisclaimerIEEE

Questions about this item

How do I install these pass-through connectors and what step do people usually mess up?

Feed each conductor through the front holes before crimping, then trim the excess flush with the connector face; the common mistake is crimping before trimming, which leaves wires too long and causes poor contact.

What maintenance or replacement will these connectors need over time?

The gold-plated contacts resist corrosion, so no routine maintenance is required; replace a connector only if the latch breaks or the housing cracks from repeated insertion cycles.

What limit shows up first when running sustained data through these CAT5e connectors?

The 100 MHz bandwidth ceiling of the CAT5e specification becomes the bottleneck before the connector hardware itself limits performance.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.