TeKit
TeKit eSATAp to SATA 22pin & IDE 4pin 5V 12V Cable 50cm/1.6ft
Connects 2.5 or 3.5 SATA drives to an eSATAp port with integrated 5 V power and optional 12 V Molex for 3.5 units
- TypeeSATAp Power ESATA Combo to SATA 22pin & IDE 4pin 5V 12V for
- ColorBlack
- Length1.64ft
- Cable Length1.64 ft. (0.50m)
- Connector Number3
- Connector DetaileSATAp Power ESATA Combo to SATA 22pin & IDE 4pin 5V 12V for
- Connect 2.5" or 3.5" SATA drives externally via eSATAp port
- Power 2.5" drives directly from the eSATAp port without extra supply
- Run 3.5" drives by adding the included Molex power connector
- Shielded copper conductors protect data integrity across the 0.5 m link
- Male-to-male connectors join eSATAp to SATA 22-pin and IDE 4-pin interfaces
Connect 2.5" and 3.5" SATA drives externally
This cable adapts a single eSATAp port to a 22-pin SATA data and power connector plus a 4-pin Molex plug. It supports both 2.5-inch and 3.5-inch hard disks without an external enclosure. The 1.64 ft length suits desktop or bench use. Shielded copper conductors carry the signal.
Verify your host port supplies 5 V and 12 V
The host must provide a powered eSATAp port that delivers 5 V through the USB portion for 2.5-inch drives. For 3.5-inch drives the separate Molex connector must be attached to a 12 V supply. Do not connect the Molex plug when using a 2.5-inch drive. Confirm the port is labelled eSATAp before ordering.
Shielded copper holds signal quality over long
The foil shield and copper cores resist interference during sustained read or write sessions. Voltage drop across the 0.5 m run stays within SATA limits for mechanical drives. No active electronics are present, so thermal throttling does not occur. The passive design maintains consistent throughput until the drive itself reaches its own limits.
Highlights
- Connect 2.5" or 3.5" SATA drives externally via eSATAp port
- Power 2.5" drives directly from the eSATAp port without extra supply
- Run 3.5" drives by adding the included Molex power connector
- Shielded copper conductors protect data integrity across the 0.5 m link
- Male-to-male connectors join eSATAp to SATA 22-pin and IDE 4-pin interfaces
Specifications
| Brand | Tekit |
|---|---|
| Type | eSATAp Power ESATA Combo to SATA 22pin & IDE 4pin 5V 12V for 3.5" 2.5" Hard Disk Data Cable |
| Color | Black |
| Length | 1.64ft |
| Cable Length | 1.64 ft. (0.50m) |
| Connector Number | 3 |
| Connector Detail | eSATAp Power ESATA Combo to SATA 22pin & IDE 4pin 5V 12V for 3.5" 2.5" Hard Disk Data Cable |
| Terminal Gender | Male to Male |
| Specifications | eSATAp Power ESATA Combo to SATA 22pin & IDE 4pin 5V 12V for 3.5" 2.5" Hard Disk Data Cable |
| Shielding | Yes |
| Conductor | Copper Conductor |
| Features | eSATAp Power ESATA Combo to SATA 22pin & IDE 4pin 5V 12V for 3.5" 2.5" Hard Disk Data Cable |
Questions about this item
Does the 50 cm cable include a separate Molex power connector for 3.5" drives?
Yes, the cable splits into a SATA 22pin data connector and a 4pin Molex connector; the Molex must be plugged into a power supply when using a 3.5" hard disk.
Which connector should I use for a 2.5" versus a 3.5" hard disk?
For a 2.5" drive connect only the eSATAp end and the SATA 22pin end; for a 3.5" drive also attach the 4pin Molex plug to a 12V power supply.
What does the eSATAp port actually supply to the drive?
The eSATAp port delivers 5V power through its integrated USB interface, enough for a 2.5" drive, while a 3.5" drive requires the additional 12V from the Molex connector.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00114364BTC
In stock
