We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Twelve-foot 14 AWG cable with SAE plug and alligator clips, black finish

TAURKENAM

TAURKENAM 12ft 14AWG SAE to Alligator Clip Power Adapter

SKU CH-GQVP-F6HK9

12 ft 14 AWG SAE to alligator-clip adapter with built-in 20 A fuse and weatherproof covers

  • 12 ft reach for flexible battery placement
  • 14 AWG cable handles up to 20 A continuous current
  • Built-in 20 A fuse protects against overload and short circuits
  • Spare 20 A and 25 A fuses included for quick replacement
  • Weatherproof covers on SAE connector and fuse holder resist moisture

12 ft 14 AWG SAE to Alligator Clip Adapter

This 12 ft extension cable uses 14 AWG conductors with a cross-section of 2.08 mm2, which is larger than 16 AWG at 1.31 mm2. It connects a standard SAE quick-release plug to alligator clips for 12 V battery charging or maintenance. A 20 A fuse is installed in the holder, and both 20 A and 25 A spare fuses are included. The assembly is supplied new with a 12-month manufacturer warranty.

SAE Interface and 20 A Fuse Limit

The SAE connector is a widely used two-pin standard for lead-acid and lithium battery tenders, but it is rated for low-voltage direct current only. The built-in 20 A fuse sets the maximum continuous current the cable can carry before opening, so loads above that level will interrupt the circuit. Both the SAE plug and the fuse holder feature weatherproof covers to resist moisture during outdoor use. No higher-voltage or alternating-current application is supported by this adapter.

Check Polarity and Fuse Rating Before Use

Verify that the SAE polarity on your charger matches the alligator clip markings, because SAE connectors are not keyed and reverse connection can damage equipment. Ensure the 20 A fuse rating suits the charger output; if the charger can exceed 20 A, the fuse will blow and the spare 25 A fuse does not raise the cable's safe limit. Confirm the 12 ft length reaches your battery location without strain, and inspect the weatherproof covers for damage before each use.

Highlights

  • 12 ft reach for flexible battery placement
  • 14 AWG cable handles up to 20 A continuous current
  • Built-in 20 A fuse protects against overload and short circuits
  • Spare 20 A and 25 A fuses included for quick replacement
  • Weatherproof covers on SAE connector and fuse holder resist moisture

Specifications

No published specifications for this item yet.

Questions about this item

How do I choose between the 20A and 25A spare fuses supplied with the 14AWG cable?

Use the 20A fuse for standard 12V charging circuits; fit the 25A spare only if your charger manual specifies a higher rating and the 14AWG conductors can handle the load.

What does the 14AWG rating mean for actual current delivery on a 12ft run?

The 2.08 mm² copper cross-section supports the fitted 20A fuse continuously, with lower voltage drop than thinner 16AWG wire over the 3.66 m length.

Is the SAE connector on this adapter a standard two-pin type compatible with common battery tenders?

Yes, it uses the industry-standard SAE two-pin quick-release plug found on most 12V battery chargers and maintainers.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.