We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Four square 120 mm fans with transparent blades and a small remote control

SXDOOL

SXDOOL 4×120 mm PWM RGB case fan kit with remote

SKU CH-3TK8-PQ94W

Four 120 mm PWM RGB case fans with hydraulic bearings, 600–1200 RPM, 20.34 CFM airflow and 28 dBA noise, plus a remote for colour and speed control

  • Fan Counts4 Fans
  • TypeCase Fan
  • Fan Thickness25mm
  • Bearing TypeHydraulic
  • RPM<1600 RPM
  • Air Flow20-25 CFM
  • RGB lighting adds colour to your build
  • PWM control adjusts fan speed from 600 to 1200 RPM
  • Hydraulic bearing rated for 40000 hours of operation
  • Low noise level at 28 dBA for quiet computing
  • Remote controller manages lighting and speed without software

Four-fan RGB PWM kit with remote

The SXDOOL kit supplies four 120 mm case fans that run on 12 V PWM power and addressable 5 V RGB LEDs. A dedicated remote controller lets users change colours and speed without opening the chassis or using motherboard software. The hydraulic bearings are rated for 40000 hours of continuous operation.

Remote simplifies wiring and control

Each fan terminates in a mini 6-pin connector that plugs into the supplied hub, so only one cable runs to the motherboard PWM header and one to a 5 V LED header. The remote adjusts both fan speed and lighting modes directly, avoiding BIOS fan-curve tuning. Builders must ensure the case has four 120 mm mounting points and that the motherboard provides a standard 4-pin PWM header plus a 5 V 3-pin ARGB header.

Practical limits of the PWM and ARGB interface

Speed range is 600 to 1200 RPM with a tolerance of ten percent, delivering 20.34 CFM at 28 dBA. The 12 V fan circuit draws 0.19 A per unit while the 5 V LED circuit draws 0.23 A per unit, so the motherboard headers must supply sufficient current for all four fans simultaneously. The 25 mm thickness fits standard 120 mm mounts but may conflict with very slim radiators or tight side-panel clearances.

Highlights

  • RGB lighting adds colour to your build
  • PWM control adjusts fan speed from 600 to 1200 RPM
  • Hydraulic bearing rated for 40000 hours of operation
  • Low noise level at 28 dBA for quiet computing
  • Remote controller manages lighting and speed without software

Specifications

BrandSXDOOL
Fan Counts4 Fans
TypeCase Fan
Fan Thickness25mm
Bearing TypeHydraulic
RPM<1600 RPM
Air Flow20-25 CFM
Noise Level25 - 30 dBA
ColorMulticolor
LEDRGB

Questions about this item

How can I confirm the fans are spinning at the correct speed after installation?

Use BIOS or fan-control software to verify each fan reports between 600 and 1200 RPM with a tolerance of roughly ten percent.

What comes in the box and which cables or connectors must be purchased separately?

The kit includes four 120 mm fans and a remote controller; each fan uses a mini 6-pin connector, so ensure your motherboard or hub has matching headers or buy an adapter.

Which version or capacity should I choose for a standard ATX build?

This single kit provides four 120 mm fans rated at 20.34 CFM and 28 dBA, suitable for most mid-tower airflow configurations.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.