We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Two black Molex-to-4-SATA power adapter cables

sakose

sakose BYTECC SATA4-POWER Molex to 4 SATA power cable 2-pack

SKU CH-58RP-4RQ9K

Converts a Molex LP4 connector into four SATA power connectors for up to four drives, two cables per pack

  • TypePower
  • ColorBlack
  • Connector Number5
  • Connector Detail4 Pins Molex Connector to 4 x Serial SATA
  • Terminal GenderMale to Male
  • SpecificationsSATA4-POWER 4 Pins Molex Connector to 4 Serial ATA Power Cab
  • Converts a Molex LP4 connector into four SATA power ports for multiple drives
  • Two cables included to support up to eight SATA devices from two Molex sources
  • Black 5-connector design with male-to-male terminals for direct PSU-to-device power
  • Powers HDDs, ODDs and add-on cards from a single Molex output
  • Simplifies RAID builds by expanding limited SATA power connectors on the PSU

BYTECC SATA4-POWER 2-Pack Adapter

This two-pack of black BYTECC SATA4-POWER cables converts each Molex LP4 connector into four SATA power plugs. Each cord carries five connectors in a male-to-male layout. The pair gives eight total SATA power outputs for drives, optical units or add-in cards. Ideal for power supplies lacking native SATA leads.

Suits builders adding multiple SATA devices

Fits systems with spare Molex ports that need to run several hard drives, optical drives or controller cards from one lead. RAID arrays benefit from the consolidated wiring. Not for setups that require native SATA headers from the PSU. Buyers needing right-angle plugs or longer cable runs should look elsewhere.

Molex LP4 to four SATA power per cable

The single specification that decides fit is the 4-pin Molex LP4 input splitting to four serial ATA power outputs on each cord. Verify your power supply has free Molex connectors before buying. No other adapters or voltage conversion is included.

Highlights

  • Converts a Molex LP4 connector into four SATA power ports for multiple drives
  • Two cables included to support up to eight SATA devices from two Molex sources
  • Black 5-connector design with male-to-male terminals for direct PSU-to-device power
  • Powers HDDs, ODDs and add-on cards from a single Molex output
  • Simplifies RAID builds by expanding limited SATA power connectors on the PSU

Specifications

BrandBYTECC
ModelSATA4-POWER
TypePower
ColorBlack
Connector Number5
Connector Detail4 Pins Molex Connector to 4 x Serial SATA
Terminal GenderMale to Male
SpecificationsSATA4-POWER 4 Pins Molex Connector to 4 Serial ATA Power Cable

Questions about this item

Will the 4-pin Molex end plug into a standard LP4 power-supply connector?

Yes, the male 4-pin Molex connector is built to the LP4 standard and fits any matching female LP4 output on the power supply.

Do I need any tools to attach the four SATA power plugs to my drives?

No tools are required; each SATA power connector is a simple push-fit male plug that seats by hand into the drive’s power port.

If one of the four SATA connectors stops delivering power, can I replace just that lead?

The cable is a single moulded assembly, so an individual lead cannot be swapped; the whole cord would need to be replaced.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.