We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 14 AWG speaker wire with red JST XH 2.54 mm connectors, 150 mm length, 20 sets

RCA WD100*2 14 AWG speaker wire 150mm 20 sets

SKU CH-WHAK-XBJM5

Twenty sets of JST XH 2.54 mm 3-pin male and female connectors on 150 mm 26 AWG tinned copper leads

  • ColorBlack
  • Connector Number2
  • SpecificationsSmall, daier, 26, Red, 10, Copper,Plastic, 120, WD100*2
  • Wire Gauge14 AWG
  • ConductorCopper Conductor
  • FeaturesSmall, 26, Copper,Plastic, Red, 120, 10, daier
  • 20 matched connector pairs simplify wiring jobs
  • 14 AWG copper conductors handle speaker-level current
  • 150 mm leads fit tight enclosure spaces
  • 54 mm JST XH pitch matches standard headers
  • Tinned copper strands resist oxidation for lasting contact

Ready-to-use speaker wiring

This pack contains twenty pre-assembled JST XH 2.54 mm three-pin male and female connector pairs. Each lead is 150 mm long and built with 26 AWG tinned copper wire for reliable signal transfer. The plastic housings lock securely, making them suitable for audio, robotics, lighting and control-panel projects. No soldering or crimping is required before installation.

Build quality and daily handling

Tinned copper conductors resist oxidation while the moulded plastic heads provide strain relief at every connection point. The 2.54 mm pitch matches standard JST XH headers found on many PCBs, so the cables plug straight into speaker terminals, battery packs or control boards. Their short 5.9-inch length keeps wiring tidy inside enclosures and reduces excess slack that can snag during maintenance.

Upgrading from raw cable

These assemblies replace hand-cut wires and loose crimp pins that can loosen over time. The jump is worth it when you need consistent, repeatable connections across multiple units such as speaker arrays, sensor clusters or prototype boards. Builders who require a different pin count, longer runs or heavier gauge cable should look elsewhere.

Highlights

  • 20 matched connector pairs simplify wiring jobs
  • 14 AWG copper conductors handle speaker-level current
  • 150 mm leads fit tight enclosure spaces
  • 54 mm JST XH pitch matches standard headers
  • Tinned copper strands resist oxidation for lasting contact

Specifications

BrandRCA
ModelWD100*2
ColorBlack
Connector Number2
SpecificationsSmall, daier, 26, Red, 10, Copper,Plastic, 120, WD100*2
Wire Gauge14 AWG
ConductorCopper Conductor
FeaturesSmall, 26, Copper,Plastic, Red, 120, 10, daier

Questions about this item

What is the 2.54 mm pitch JST XH connector used for?

The 2.54 mm pitch JST XH connector joins the 150 mm 26 AWG leads to speakers, audio gear, robots or PCB control panels.

What clearance does the 150 mm cable with JST XH plugs need?

Allow at least 150 mm straight run plus room for the 2.54 mm pitch male and female housings to seat without strain.

How do you install the JST XH plugs and what step is often missed?

Push each 2.54 mm pitch JST XH plug straight in until the latch clicks; the common error is stopping before the latch engages.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.