We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black sleeved Molex to three 3-pin fan Y-cable, 30cm

Phobya

Phobya 81104 4-Pin Molex to 4x 3-Pin 12V 30cm Sleeved Black chipset cooling

SKU CH-ABYT-WRPXS MPN 81104

Converts one Molex connector into four 3-pin fan headers with a 30 cm sleeved black cable

  • Fan ColorBlack
  • FeaturesPhobya 4-Pin Molex power cable that converts a single Molex
  • Connect up to four fans from one Molex connector
  • 30 cm sleeved cable keeps builds tidy
  • Loop-through Molex preserves the original power socket
  • White RPM marking identifies the signal wire
  • Black mesh sleeve and heatshrink for a clean look

4-Pin Molex Fan Splitter for Chipset Cooling

This Phobya 81104 cable converts a single 4-pin Molex power connector into three 3-pin fan headers, letting you run multiple chipset or memory fans from one supply rail. The 30 cm sleeved loom keeps wiring tidy inside compact builds. A white marking on one branch identifies the RPM signal wire for monitoring. Builders who need more than three additional fan headers cannot use this adapter alone.

Plug-and-Play Installation with Molex Loop-Through

Connect the male Molex plug to any free PSU lead, then attach up to three 3-pin fans to the female headers. The loop-through Molex female on the input side preserves the original connector for another device. Black mesh sleeving and heatshrink ends resist snagging during routing. Installers must ensure the 12 V Molex rail can supply the combined current draw of all attached fans.

Fixed 12 V Operation Limits Speed Control

The adapter passes the Molex 12 V line directly to every 3-pin header, so all connected fans run at full voltage continuously. PWM or voltage-based fan curves are not possible because the 3-pin headers lack a fourth control wire. The single RPM signal wire only reports speed from one fan, leaving the others unmonitored. Systems requiring per-fan speed regulation need a powered fan controller instead.

Highlights

  • Connect up to four fans from one Molex connector
  • 30 cm sleeved cable keeps builds tidy
  • Loop-through Molex preserves the original power socket
  • White RPM marking identifies the signal wire
  • Black mesh sleeve and heatshrink for a clean look

Specifications

BrandPhobya
Model81104
Fan ColorBlack
FeaturesPhobya 4-Pin Molex power cable that converts a single Molex power connector into three 3-pin fan connectors. Comes sleeved black and 30cm long.

Questions about this item

How can I confirm the Phobya 81104 cable is delivering 12 V power to all four fans after installation?

Check that each connected fan spins up and reports an RPM reading in your BIOS or monitoring software; the white marking on one split cable indicates which lead carries the speed signal back to the motherboard header.

What connectors are included with the Phobya 81104 and what must I provide separately?

The cable supplies one 4-pin Molex male plug and three 3-pin fan headers plus a loop-through Molex female; you must provide the 4-pin Molex power lead from your PSU and up to four 3-pin fans yourself.

Which Phobya 81104 variant should I choose for a standard 30 cm reach with black sleeving?

Model 81104 is the single version offered; it provides a 30 cm black-sleeved assembly with 12 V pass-through, so no alternative length or colour options exist to select from.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.