Netgear QL-DC-DC30V3.5A 9V-28V to 30V 3.5A Step-Up Power Adapter Cord
A 9 V to 28 V input step-up cable delivers a steady 30 V at 3.5 A for Starlink Mini, with IP68 protection and 100 W maximum output
- TypeSpeaker Wires
- ColorYellow
- Length3 Feet
- Connector Number3
- Terminal GenderMale to Female
- Wire Gauge2 AWG
- Converts 9 V–28 V input to a steady 30 V 3.5 A output for Starlink Mini
- IP68 waterproof rating protects against dust, water and harsh outdoor conditions
- 2 ft DC cord plus 1.6 ft silicone wire gives flexible, portable placement
- Built-in safety protections guard against voltage fluctuations for uninterrupted service
- Plug-and-play design requires no configuration — just connect and power up
Starlink Mini power conversion
This Netgear step-up adapter cord converts a 9V to 28V DC source into a stable 30V 3.5A output for the Starlink Mini router. It is built for users who need to run the terminal from 12V or 24V vehicle, RV or portable battery systems. The IP68-rated assembly resists dust, water, UV and corrosion in outdoor environments. A 3.2-foot DC cord and 1.6-foot silicone lead give flexible placement.
Replaces fixed-voltage supplies
The cable removes the need for a mains-only power brick when a 12V or 24V DC source is already available. It is worth the switch when the installation cannot reach AC power but can tap a vehicle or battery bank. The converter maintains a steady 30V output despite input fluctuations across the 9V to 28V range. Buyers who only have access to standard wall outlets will not need this adapter.
Sustained 100W delivery
The unit is rated for a maximum continuous output of 100W, so the 30V 3.5A load can be maintained without thermal throttling. Multiple protection circuits guard against over-voltage, over-current and short-circuit conditions during long runs. The ruggedised, waterproof housing keeps performance consistent in snow, wind and direct sunlight. No active cooling is used, so silent operation is preserved.
Highlights
- Converts 9 V–28 V input to a steady 30 V 3.5 A output for Starlink Mini
- IP68 waterproof rating protects against dust, water and harsh outdoor conditions
- 2 ft DC cord plus 1.6 ft silicone wire gives flexible, portable placement
- Built-in safety protections guard against voltage fluctuations for uninterrupted service
- Plug-and-play design requires no configuration — just connect and power up
Specifications
| Brand | Netgear |
|---|---|
| Model | QL-DC-DC30V3.5A |
| Type | Speaker Wires |
| Color | Yellow |
| Length | 3 Feet |
| Connector Number | 3 |
| Terminal Gender | Male to Female |
| Wire Gauge | 2 AWG |
| Specifications | Type A, 30 volts, 12, inches, Male-to-Female, 2, QL-DC-DC30V3.5A |
| Features | Type A, Male-to-Female, 30 volts, 3.2 feet |
Questions about this item
What input voltage range does the 9V-28V to 30V step-up adapter accept?
The adapter accepts a 9V to 28V DC input range, suitable for 12V and 24V vehicle or battery systems.
How do I connect the 3.2 ft DC cord and 1.6 ft silicone wire to the Starlink Mini?
Plug the male DC connector into your 12V or 24V source, then connect the female end to the Starlink Mini power port; no configuration is required.
When should I replace the IP68 waterproof converter if used outdoors continuously?
Replace the unit if the yellow cable jacket shows cracking, the connectors corrode, or the 30V 3.5A output becomes unstable under load.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00114323BTC
In stock
