We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black ABS USB to RS485/422 adapter with .5m shielded cable

LORDWORLD

LORDWORLD DT-5119 USB RS485/422 Adapter .5m

SKU CH-BWSV-A9RFM

A .5 m USB link for RS-485 and RS-422 serial lines, built with 24 AWG double-shielded cable and an FTDI FT232RL plus SP485 dual chip

  • USB to RS-485/422 converter for industrial serial communication
  • FTDI FT232RL plus SP485 dual chip ensures reliable data transfer
  • Double shielding with 80 braided tinned copper strands plus aluminium foil blocks interference
  • 24WG wire with four tensile ropes and 8 mm thick jacket resists mechanical stress
  • .5 metre cable length suits compact panel or bench installations

USB to RS485/422 industrial adapter

The LORDWORLD DT-5119 converts a USB port to an EIA/TIA RS-485 or RS-422 serial interface. It targets engineers and technicians who need reliable long-distance communication with industrial equipment such as PLCs, sensors or HMIs.

Plug-and-play with shielded cable

The adapter uses an FTDI-FT232RL and SP485 dual-chip set that is supported by common operating systems without extra configuration. Its .5 metre cable has 24WG conductors, 80 braided tinned copper strands, aluminium foil shielding, four tensile ropes and a 7-core 8mm jacket to resist noise and mechanical stress.

RS-485 and RS-422 standard compliance

The single specification that decides fit is the dual-protocol support for EIA/TIA RS-485 and RS-422 on the same DB9 connector. Buyers who need RS-232 voltage levels or a different connector type cannot use this adapter.

Highlights

  • USB to RS-485/422 converter for industrial serial communication
  • FTDI FT232RL plus SP485 dual chip ensures reliable data transfer
  • Double shielding with 80 braided tinned copper strands plus aluminium foil blocks interference
  • 24WG wire with four tensile ropes and 8 mm thick jacket resists mechanical stress
  • .5 metre cable length suits compact panel or bench installations

Specifications

BrandLORDWORLD

Questions about this item

How can I confirm the DT-5119 adapter is communicating correctly after plugging it in?

Check Device Manager for a new COM port using the FTDI FT232RL chip, then open a serial terminal at the expected baud rate to verify data flows on the RS-485 or RS-422 lines.

What comes with the DT-5119 and what must I source separately?

The package includes the 0.5 m USB-to-RS485/422 cable with ABS housing, 24WG conductors, 80 braid shield and dual FT232RL plus SP485 chips; you only need to provide terminal-block wiring for your RS-485 or RS-422 device.

Which DT-5119 version should I choose for a half-duplex RS-485 network versus a full-duplex RS-422 link?

The same DT-5119 unit supports both EIA/TIA RS-485 and RS-422 standards; wire the 7-core cable in two-wire mode for RS-485 half-duplex or four-wire mode for RS-422 full-duplex.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.