We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Rectangular metal power supply with perforated sides and three output terminal blocks

LORDWORLD

LORDWORLD 12V 30A 360W AC-DC Adapter Adjustable 10.2-13.8V Three Outputs

SKU CH-M68W-TVZDJ

A 360 W AC-to-DC unit converts 110 V or 220 V mains to an adjustable 10.2 V to 13.8 V output at up to 30 A across three channels, with overload, over-voltage, thermal and short-circuit protection

  • Adjustable 10.2V to 13.8V output matches varied device needs
  • 360W at 30A powers demanding LED strips and 3D printers
  • Three output channels run multiple loads from one unit
  • Metal case with ventilation holes improves heat dissipation
  • Overload, over-voltage, thermal and short-circuit protections safeguard equipment

Power supply for 12V equipment

This LORDWORLD adapter converts 110V or 220V AC mains into a regulated 12V DC output rated at 30A and 360W. The voltage can be trimmed by 15% between 10.2V and 13.8V to suit sensitive loads. Three parallel output channels share the total current, so a single device drawing up to 30A can be powered from any terminal. It is intended for indoor use with LED strips, 3D printers, ham radio transceivers, audio amplifiers or similar 12V gear.

Mains voltage and load check

Verify that your local supply is 110V or 220V AC before connecting the unit. Confirm that the connected equipment operates on 12V DC and will not exceed the 30A continuous limit; drawing more than 30A will damage the supply. Ensure the installation location is indoors and provides airflow around the ventilated metal case for heat dissipation. No other electrical parameters need to be matched.

Suitable for fixed 12V loads up to 30A

This unit suits builders who need a single adjustable 12V source with multiple output terminals for indoor projects. It is not for buyers who require battery-backed output, outdoor-rated enclosures, higher current than 30A, or a different output voltage range. Users needing remote sensing, medical-grade isolation or redundant parallel supplies should look at other product types.

Highlights

  • Adjustable 10.2V to 13.8V output matches varied device needs
  • 360W at 30A powers demanding LED strips and 3D printers
  • Three output channels run multiple loads from one unit
  • Metal case with ventilation holes improves heat dissipation
  • Overload, over-voltage, thermal and short-circuit protections safeguard equipment

Specifications

BrandLORDWORLD

Questions about this item

What comes in the box and do I need any extra cables or connectors?

The adapter ships as a single unit with three built-in output channels; you only need to supply your own AC mains lead and the DC wiring for each load.

Should I pick the 10.2 V or 13.8 V setting for a typical 12 V LED strip?

Leave the trimmer at the factory 12 V centre; the 15 % range lets you fine-tune between 10.2 V and 13.8 V if a specific strip needs a slight offset.

How much current will the unit actually deliver when my 3D printer draws 25 A?

It supplies exactly what the load demands up to 30 A, so a 25 A draw receives 25 A; exceeding 30 A triggers protection and can damage the supply.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.