We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
White rectangular push-button switch with 118-inch cable and adhesive mount

LHKLUK KG-A PC Power Button White 118" Cable ATX Splitter Adhesive Mount

SKU CH-SCZX-C4MJ0

External ATX power switch with 118-inch cable, LED indicator, adhesive mount and splitter for dual-button control

  • TypePush Buttons
  • Switch FunctionON-OFF
  • Voltage5 volts
  • Housing MaterialPlastic
  • Mounting StyleWall Mount
  • Size/Dimensions1.8 cm x 11.9 cm x 18 cm
  • Control PC from desk with 118" cable reach
  • LED shows power state at a glance
  • Adhesive mount installs in seconds no drilling
  • Splitter keeps original case button working too
  • IP65 rated switch survives dust and splashes

External ATX Power Switch

This push-button switch adds an external power control for desktop computers with ATX motherboards. It connects via a standard 4-pin header and includes a 1-to-2 splitter so the original case button remains functional. The 118-inch cable suits desk, rack or floor placement. It is not intended for laptop use.

IP65 Rating and Low Current Draw

The plastic housing carries an IP65 rating for dust and water-jet protection. Operating voltage is 5 volts with a current draw of 0.01 amps. The switch functions across a temperature range of 0 to 100 degrees Celsius. No active cooling or additional power supply is required.

Adhesive Mount for Sustained Use

A 3M adhesive sticker secures the switch to a desk or panel without drilling. The 118-inch cable routes through drive bays, expansion slots or rear vents for a permanent installation. The splitter board maintains dual-switch operation continuously during extended sessions.

Highlights

  • Control PC from desk with 118" cable reach
  • LED shows power state at a glance
  • Adhesive mount installs in seconds no drilling
  • Splitter keeps original case button working too
  • IP65 rated switch survives dust and splashes

Specifications

TypePush Buttons
BrandLHKLUK
Switch FunctionON-OFF
ModelKG-A
Voltage5 volts
Housing MaterialPlastic
Mounting StyleWall Mount
Size/Dimensions1.8 cm x 11.9 cm x 18 cm
MaterialPlastic
Standards/CertificationsIP65, 0
Horsepower0.01 amps
Operating Temperature0 degrees_celsius to 100 degrees_celsius
Color/FinishWhite
Operating Frequencynot_applicable
DutyDesktop Computers with ATX Motherboards
Compatibility/FitmentDesktop Computers with ATX Motherboards
Resolution1
Display TypeKG-A118
Color DisplayWHITE
FeaturesDesktop Computers with ATX Motherboards
Part NumberKG-A118

Questions about this item

How do I install the KG-A power button on my desk without drilling?

Peel the 3M adhesive stickers, press the 1.8 cm × 11.9 cm housing onto a clean desk or panel, route the 118" cable to the motherboard JFP1/F_PANEL header, and match POWER SW to SW_PW and LED+/- to PLED+/- pins.

Will the white LED indicator or the push-button switch wear out first?

The mechanical push-button is rated for repeated actuation, while the LED runs at 5 volts and .01 amps; under normal desktop use the switch mechanism typically reaches end-of-life before the indicator dims.

What thermal limit stops the KG-A from working during a long rendering session?

Operating temperature is specified from 0 to 100 degrees Celsius; sustained chassis heat above 100 °C will cause the switch to shut down before the IP65-rated housing is compromised.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.