LetLinkSo
LetLinkSo LLS-CB-1MC1ED-01 PCIe 5.0 MCIO x4 to EDSFF 1C Cable 1.6ft
Connects a PCIe 5.0 MCIO x4 host to E1.S, E1.L, E3.S or E3.L SSDs at 32 GT/s per lane over a 1.6 ft copper cable with integrated 15-pin power
- TypePCIe 5.0
- ColorBlack
- Length1.6ft(50 cm)
- Connector Number2
- Connector Detail1 x MCIOx4 to 1 x EDSFF
- Terminal GenderMale to Male
- PCIe 5.0 at 32 GT/s per lane delivers blistering throughput
- 15-pin power integrated into the EDSFF connector simplifies cabling
- Supports E1.S, E1.L, E3.S and E3.L drives for broad server compatibility
- 6 ft (50 cm) copper construction preserves signal integrity at speed
- Hot-swappable design allows drive changes without system reboot
Purpose-built PCIe 5.0 interconnect
The LetLinkSo LLS-CB-1MC1ED-01 is a 1.6ft cable that links an MCIO x4 host port to a single EDSFF 1C drive connector. It targets server and storage builders who need PCIe 5.0 throughput for E1.S, E1.L, E3.S or E3.L solid-state devices. The assembly carries both signal and 15-pin power through a male-to-male copper conductor.
Straightforward rack installation
The 50 cm length fits typical 1U/2U cable routing without excess slack. Male-to-male terminals plug directly into the backplane and drive cage; no adapters or tools are required. Hot-swap capability lets technicians replace drives without powering down the chassis. The only common pitfall is reversing the connector orientation — keyed shrouds prevent damage but demand attention during the first mate.
Suited for dense PCIe 5.0 storage deployments
This cable serves integrators populating EDSFF bays from an MCIO x4 source at 32 GT/s per lane. It is not for environments that rely on SAS signalling or legacy backplanes lacking MCIO ports. Buyers needing multi-drive breakout cables, longer runs for full-rack cabling, or right-angle connectors for tight clearance should look at other configurations.
Highlights
- PCIe 5.0 at 32 GT/s per lane delivers blistering throughput
- 15-pin power integrated into the EDSFF connector simplifies cabling
- Supports E1.S, E1.L, E3.S and E3.L drives for broad server compatibility
- 6 ft (50 cm) copper construction preserves signal integrity at speed
- Hot-swappable design allows drive changes without system reboot
Specifications
| Brand | LetLinkSo |
|---|---|
| Model | LLS-CB-1MC1ED-01 |
| Type | PCIe 5.0 |
| Color | Black |
| Length | 1.6ft(50 cm) |
| Connector Number | 2 |
| Connector Detail | 1 x MCIOx4 to 1 x EDSFF |
| Terminal Gender | Male to Male |
| Speed | 32 GT/s (per lane) |
| Conductor | Copper Conductor |
| Features | BLAZING SPEEDS |
Questions about this item
How can I verify the cable is running at the full PCIe 5.0 32 GT/s rate after installation?
Check the link speed reported by the host system or drive firmware; it should show 32 GT/s per lane on the x4 connection.
What connectors and power leads are included with the 1.6ft cable?
The cable has a male MCIO x4 connector on one end and a male EDSFF 1C connector with a 15-pin power segment on the other.
Which EDSFF drive form factors does this MCIO x4 cable support?
It is built for E1.S, E1.L, E3.S and E3.L solid-state drives.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00115115BTC
In stock
