We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Ten brass push-fit adapters with silver finish, 1/8 inch connections

Legris

Legris 3014 53 11 push-fit adapter 1/8 in 290 psi pack 10

SKU CH-BPQZ-Y7RYA MPN 3014

A pack of ten brass push-fit adapters connects 1/8 in tubing to 1/8 in FNPT threads at up to 290 psi and 175 °F

  • TypeDrain Components
  • MaterialHAWA
  • Push-to-connect design speeds installation with no tools required
  • 290 psi rating handles high-pressure pneumatic lines reliably
  • Brass C36000 body resists corrosion for long service life
  • 1/8 in push-to-connect and FNPT ends join metric and imperial systems
  • Pack of 10 fittings covers multiple connection points in one order

Push-fit adapter for 1/8 in tubing

This brass push-fit adapter connects 1/8 in outer-diameter tube to a 1/8 in FNPT thread. It is rated for 290 psi maximum operating pressure and 175 Degrees F maximum temperature. The fitting uses C36000 brass and has an overall length of 7/8 in. Supplied as a pack of 10 for plumbing and vacuum applications.

Suits vacuum and low-pressure plumbing lines

Installers who need a quick-connect joint between 1/8 in tube and a female pipe thread will find this fitting matches the required size and pressure rating. It is not intended for systems that exceed 290 psi or 175 Degrees F, nor for tube sizes other than 1/8 in OD. Buyers needing different thread forms, larger diameters or higher temperature ratings should select alternative fittings.

1/8 in push-to-connect to 1/8 in FNPT

The critical specification is the combination of a 1/8 in push-to-connect end and a 1/8 in FNPT thread end with a 290 psi pressure limit. Verify that both the tube outer diameter and the mating thread match these dimensions before ordering. The C36000 brass body and 7/8 in overall length are fixed by the design.

Highlights

  • Push-to-connect design speeds installation with no tools required
  • 290 psi rating handles high-pressure pneumatic lines reliably
  • Brass C36000 body resists corrosion for long service life
  • 1/8 in push-to-connect and FNPT ends join metric and imperial systems
  • Pack of 10 fittings covers multiple connection points in one order

Specifications

TypeDrain Components
MaterialHAWA
BrandLegris
Model3014 53 11

Questions about this item

Does the brass push-fit adapter get hot or noisy when it runs continuously at 290 psi?

The fitting has no moving parts and generates no heat or noise; it simply holds pressure up to 290 psi at temperatures up to 175 °F.

What tubing and thread sealant must I already have to install the 1/8 in push-to-connect side?

You need 1/8 in OD tubing compatible with push-to-connect fittings and your own thread sealant for the 1/8 in FNPT side, because none is pre-applied.

Will the C36000 brass body corrode when paired with older steel or copper pipe threads?

C36000 brass resists dezincification and is compatible with standard 1/8 in NPT threads on legacy steel or copper piping.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.