We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Yellow 10 m duplex LC-to-LC singlemode fiber patch cable with 2.0 mm jacket

Intellinet Network Solutions

Intellinet Network Solutions Singlemode Duplex BIF LC to LC Fiber Patch Cable 10 m 9/125 µm Yellow

SKU CH-ERG2-MXKKW

A 10 m singlemode duplex patch cable with LC connectors and bend-insensitive G.657.A1 fiber for 40G Ethernet links

  • TypeFiber
  • Connector ALC
  • Connector BLC
  • Length10 m
  • ColorYellow
  • ShieldedNo
  • Ideal for data centres and telecom rooms with versatile interconnect design
  • UPC connectors improve return loss for cleaner signal transmission
  • OS2 single-mode fibre supports 40G Ethernet and higher speeds
  • Bend-insensitive G.657.A1 fibre reduces attenuation when routed tightly
  • Corning ultra-pure glass core delivers low loss over 10 m length

Singlemode 10 m Duplex Patch Cable

This 10 m yellow patch cable uses OS2 singlemode fiber with 9/125 µm cores and LC/UPC connectors on both ends. Bend-insensitive glass rated to G.657.A1 reduces attenuation when the cable is routed through tight paths. It is built for interconnect and cross-connect work in entrance facilities, telecom rooms, data centres and desk-side connections.

Upgrade from Multimode or Standard Singlemode

The jump is worthwhile when links must run longer than multimode allows or when 40 Gbit/s Ethernet and higher data rates are required. Standard singlemode without bend-insensitive glass loses more signal in dense patch panels or sharp bends, so this cable suits installs that cannot guarantee generous bend radii.

Build Integration: LC UPC Interfaces and OFNR Rating

Each end terminates in an LC UPC connector, so the equipment on both sides must present LC ports with UPC polish. The OFNR jacket suits in-building riser and general-purpose horizontal runs. Corning ultra-pure glass and the included test report verify link loss before the cable goes live.

Highlights

  • Ideal for data centres and telecom rooms with versatile interconnect design
  • UPC connectors improve return loss for cleaner signal transmission
  • OS2 single-mode fibre supports 40G Ethernet and higher speeds
  • Bend-insensitive G.657.A1 fibre reduces attenuation when routed tightly
  • Corning ultra-pure glass core delivers low loss over 10 m length

Specifications

BrandIntellinet Network Solutions
ModelSinglemode Duplex BIF
TypeFiber
Connector ALC
Connector BLC
Length10 m
ColorYellow
ShieldedNo
Features9/125 µm, Bend Insensitive Fiber Cable G.657.A1

Questions about this item

What size patch panel or tray can hold the 2.0 mm duplex jacket?

The 2.0 mm yellow duplex jacket fits standard LC duplex cut-outs and common 1U patch panels with no special brackets required.

How do I seat the LC UPC connectors without damaging the ceramic ferrules?

Push each LC connector straight in until the latch clicks; do not twist or rock the ferrule, as side force can chip the UPC polish.

When should I plan to re-terminate or replace the cable?

Re-terminate only if the end-face inspection shows scratches or contamination that cleaning cannot remove; the Corning G.657.A1 fiber itself is rated for the life of the installation.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.