We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Yellow duplex fiber patch cable LC to SC connectors 6 m

Intellinet Network Solutions

Intellinet Network Solutions 6 m LC to SC UPC Singlemode Duplex BIF 9/125 µm Yellow 2.0 mm OFNR G.657.A1

SKU CH-AVEM-ARB7K

A 6-metre single-mode duplex patch cable with LC and SC UPC connectors, bend-insensitive G.657.A1 fibre and Corning glass for low-loss 40G links

  • TypeFiber
  • Connector ALC
  • Connector BSC
  • Length6 m
  • ColorYellow
  • ShieldedNo
  • Ready for 40 G Ethernet with low signal loss and high data rates
  • Bend-insensitive G.657.A1 fiber reduces attenuation when cables are routed tightly
  • UPC polished connectors give better surface finish and lower return loss
  • Corning ultra-pure glass core delivers low attenuation for long-distance links
  • Six-metre yellow duplex patch cord with LC to SC ends for single-mode networks

6 m LC/SC UPC Singlemode Duplex

This 6 m singlemode duplex patch cable uses LC and SC connectors with UPC polish for low return loss. It is built with 9/125 µm bend-insensitive fiber rated to G.657.A1 and meets OFNR fire ratings. The yellow jacket identifies it as a singlemode run for indoor backbone or horizontal links.

Replaces standard singlemode patch cords

The bend-insensitive G.657.A1 construction reduces attenuation when the cable is routed around tight corners or through dense panels. That makes the jump worthwhile whenever existing cables show excess loss after moves, adds or changes in entrance facilities, telecom rooms or data-centre cross-connects.

Sustained-load behaviour

Corning ultra-pure glass keeps attenuation low and bandwidth high over the full 6 m length, supporting 40G Ethernet and higher data rates continuously. Each unit ships with a factory test report verifying insertion loss and return loss, so performance stays consistent under long-term load rather than only in short bursts.

Highlights

  • Ready for 40 G Ethernet with low signal loss and high data rates
  • Bend-insensitive G.657.A1 fiber reduces attenuation when cables are routed tightly
  • UPC polished connectors give better surface finish and lower return loss
  • Corning ultra-pure glass core delivers low attenuation for long-distance links
  • Six-metre yellow duplex patch cord with LC to SC ends for single-mode networks

Specifications

BrandIntellinet Network Solutions
ModelSinglemode Duplex BIF
TypeFiber
Connector ALC
Connector BSC
Length6 m
ColorYellow
ShieldedNo
Features9/125 µm, Bend Insensitive Fiber Cable G.657.A1

Questions about this item

Will the 2.0 mm yellow jacket fit standard LC and SC patch panels in my rack?

Yes, the cable uses standard LC and SC connectors with a 2.0 mm jacket that fits typical patch panel ports.

What is the correct way to seat the UPC connectors so return loss stays low?

Push each connector straight in until it clicks; do not twist, as twisting degrades the UPC end-face contact.

When should I plan to replace this cable in a 40G Ethernet link?

Replace it if insertion loss rises above your link budget or if the jacket shows cracks from repeated bending.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.