We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Gray Cat6a S/FTP patch cable, 3 ft, RJ45 ends, snag-free boots

Intellinet Network Solutions

Intellinet Cat6a S/FTP Network Ethernet Cable 3 ft Gray 26 AWG

SKU CH-Z15T-Y08Y1

Cat6a S/FTP patch cable supports 10 Gbps at 500 MHz with full shielding, pure copper conductors and gold-plated RJ45 connectors

  • TypeNetwork Ethernet Cables
  • Cat6A
  • Connector ARJ45
  • Connector BRJ45
  • Length3 ft.
  • ColorGray
  • Certified Cat6a Class EA for 10 Gbps at 500 MHz per ISO/IEC 11801
  • S/FTP shielding with aluminium braid and per-pair foil blocks crosstalk and noise
  • 100 % bare copper conductors deliver full conductivity without CCA or CCS
  • 50 µin gold-plated RJ45 contacts resist corrosion for lasting signal integrity
  • Snag-free boots and heavy-duty strain relief protect connectors during frequent moves

Cat6a S/FTP 3 ft patch cable

This Cat6a S/FTP patch cable provides a 10 Gbps connection with 500 MHz bandwidth. It uses 26 AWG stranded pure copper conductors and RJ45 connectors with 50 micro-inch gold-plated contacts. The double-shielded design includes aluminum foil around each pair and an overall aluminum braid. Snag-free boots protect the connectors during installation.

Shielded copper cable for 10G upgrade

The S/FTP construction reduces near-end crosstalk when cables run parallel, supporting reliable 10GBase-T performance. It replaces unshielded or copper-clad aluminum cables that cannot meet Cat6a Class EA requirements. The pure copper conductors ensure maximum conductivity for Power over Ethernet up to IEEE 802.3bt. This cable is certified to ISO/IEC 11801 and EN 50173-1 standards.

Suited for short high-speed links

This 3-foot length suits patch-panel connections, switch-to-device links, and PoE++ deployments in racks or wall outlets. It supports both T568A and T568B wiring schemes. Installers needing longer runs, solid-core cable for in-wall termination, or unshielded cables for simpler routing should select a different product.

Highlights

  • Certified Cat6a Class EA for 10 Gbps at 500 MHz per ISO/IEC 11801
  • S/FTP shielding with aluminium braid and per-pair foil blocks crosstalk and noise
  • 100 % bare copper conductors deliver full conductivity without CCA or CCS
  • 50 µin gold-plated RJ45 contacts resist corrosion for lasting signal integrity
  • Snag-free boots and heavy-duty strain relief protect connectors during frequent moves

Specifications

BrandIntellinet Network Solutions
TypeNetwork Ethernet Cables
Cat6A
Connector ARJ45
Connector BRJ45
Length3 ft.
ColorGray
ShieldedYes

Questions about this item

Will the 26 AWG stranded conductors and snag-free boots fit through tight cable-management channels?

The 26 AWG stranded wires make the cable more flexible than solid-core versions, and the snag-free boots prevent the RJ45 tabs from catching while pulling it through trays or conduit.

Do I need a special tool or wiring scheme to terminate the RJ45 connectors on this patch cord?

The cable arrives with RJ45 plugs already crimped and wired to both T568A and T568B colour codes, so no termination tool or wiring decision is required — just plug it in.

Will the 50 micro-inch gold-plated contacts need cleaning or re-plating after repeated PoE++ cycles?

The 50 micro-inch gold plating resists corrosion from repeated PoE++ insertion cycles, so routine cleaning or re-plating is not necessary under normal use.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.