We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black metal bracket with detachable side wings, two SATA data cables and two power cables included

Inateck 2.5 to 3.5 Adapter ST1004 with SATA Cables

SKU CH-3N16-F8RB3

Mounts one or two 2.5" drives in a 3.5" bay and includes two SATA III cables plus power cables and screws

  • ColorBlack
  • Dimensions138.0 in x 100.0 in x 21.0 in
  • Package Contentscables and bracket
  • Mount one or two 2.5″ drives in a 3.5″ bay
  • Detachable side wings free space for single-drive setups
  • Two 6 Gbps SATA data cables included for full bandwidth
  • 4-pin and 15-pin power cables plus screwdriver and 16 screws supplied
  • Bottom screw holes and hollow vents improve stability and airflow

2.5 to 3.5 Drive Mounting Kit

The Inateck ST1004 bracket lets builders install one or two 2.5 inch hard drives or SSDs into a single 3.5 inch internal bay of an ATX case. It includes two SATA III data cables rated for 6Gbps, two SATA power cables, a screwdriver and sixteen mounting screws. The side wings detach when only one drive is fitted, saving space inside the chassis. This kit is not for builders who need to mount 3.5 inch drives or who require tool-free drive trays.

Dual Drive Support in One Bay

The bracket accepts either a single 2.5 inch drive or two 2.5 inch drives simultaneously, making it the deciding spec for users with limited bay count. Mounting holes on the bottom allow installation from the side or the bottom of the bay for a secure fit. All necessary cables and hardware are supplied so no extra parts are required. It does not suit builds that need hot-swap capability or support for drives thicker than the standard 2.5 inch form factor.

Passive Cooling With Open Design

Hollow sections on the base and detachable wings promote airflow around the installed drives without adding a fan. The iron bracket acts as a heat spreader, drawing warmth away from the drive bodies during normal operation. Power is delivered through the included 4 pin to dual 15 pin and 15 pin to dual 15 pin SATA power cables. The kit adds no active noise and draws no power of its own.

Highlights

  • Mount one or two 2.5″ drives in a 3.5″ bay
  • Detachable side wings free space for single-drive setups
  • Two 6 Gbps SATA data cables included for full bandwidth
  • 4-pin and 15-pin power cables plus screwdriver and 16 screws supplied
  • Bottom screw holes and hollow vents improve stability and airflow

Specifications

BrandInateck
ColorBlack
Dimensions138.0 in x 100.0 in x 21.0 in
Package Contentscables and bracket

Questions about this item

What does the 6Gbps SATA III rating mean when the cables are connected to a 2.5" drive in a 3.5" bay?

The two included SATA III data cables each support 6Gbps bandwidth and are backward compatible with SATA I and II, so the drive will run at the maximum speed its own controller allows.

How do the SATA power cables connect to a standard power supply and the adapted drives?

One cable converts a 4-pin Molex connector to two 15-pin SATA power plugs, while the other splits a single 15-pin SATA power connector into two, giving two ways to power both drives.

What are the bracket's exact dimensions and screw-hole layout for fitting into a 3.5" drive bay?

The iron bracket measures 138mm x 100mm x 21mm, weighs 91.8g, and has screw holes on the bottom and side wings for secure side or bottom mounting in a standard 3.5" bay.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.