We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Gray industrial pin-and-sleeve plug with aluminum shroud and locking ring

Hubbell Incorporated

Hubbell HBL560PS1W Pin & Sleeve Plug 60 A 600 V AC

SKU CH-SA70-BFDR4

Industrial pin-and-sleeve plug rated 60 A, 600 V AC with Valox 357 housing, aluminum shroud, UL Type 4X watertight seal, brass sleeve contacts and #6–#4 AWG wire capacity

  • Color/FinishGray
  • Color MappingGray
  • TypeLight Switch
  • 60 A 600 V AC rating powers heavy industrial loads
  • Valox 357 housing with aluminum shroud resists impact and corrosion
  • UL Type 4X watertight and dust-tight seal protects in harsh environments
  • Brass sleeve contacts ensure reliable conductivity across -40 °C to +75 °C
  • Accepts #6 AWG to #4 AWG wire with .50 in to 1.45 in cable diameter

Industrial Pin & Sleeve Plug

The Hubbell HBL560PS1W is a 60 amp, 600 volt AC plug built for industrial and commercial power connections. It suits facilities that need a watertight, locking connector for heavy-duty equipment. The four-pole, five-wire configuration handles three-phase loads with a ground. Electricians and maintenance teams specify it for permanent or temporary high-current feeds.

Valox Housing With Aluminium Shroud

A composite body uses Valox 357 non-metallic housing paired with an aluminium shroud for impact resistance. The locking ring creates a UL Type 4X watertight and dust-tight seal when mated. All-brass sleeve contacts and pressure terminal screws accept wire from #6 AWG to #4 AWG. Cable diameter range spans 0.50 inches to 1.45 inches for flexible cord selection.

Replaces Worn Or Non-Watertight Plugs

Upgrade when existing plugs show contact wear, cracked housings or lost sealing in wet or dusty environments. The CSA C22.2 No.159 and UL 1682, UL50, UL1010 listings support code-compliant replacements. The jump is worth it when downtime from connector failure costs more than the installed cost. Not for low-amperage control circuits or residential wiring.

Highlights

  • 60 A 600 V AC rating powers heavy industrial loads
  • Valox 357 housing with aluminum shroud resists impact and corrosion
  • UL Type 4X watertight and dust-tight seal protects in harsh environments
  • Brass sleeve contacts ensure reliable conductivity across -40 °C to +75 °C
  • Accepts #6 AWG to #4 AWG wire with .50 in to 1.45 in cable diameter

Specifications

BrandHUBBELL
Color/FinishGray
Color MappingGray
TypeLight Switch

Questions about this item

What voltage and current does the 4P 5W 60 A 600 V AC pin-and-sleeve plug actually deliver in service?

The plug is rated for 60 amps continuous at up to 600 VAC and 250 VDC, so the interface caps usable power at those limits in industrial and commercial installations.

What cable diameter and wire gauge must I have so the Valox 357 housing and aluminum shroud seal and clamp correctly?

It accepts 0.50 in. to 1.45 in. outside-diameter portable cord and #6 AWG to #4 AWG conductors for a watertight Type 4X fit.

How do I terminate the conductors in the pressure-terminal screws, and what step do installers most often miss?

Strip each conductor to the gauge-marked length, insert fully into the brass sleeve contacts, torque the pressure screws to spec, then engage the locking ring to complete the UL Type 4X seal — skipping the ring leaves the assembly unsealed.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.