We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 3ft right-angle XLR cable with 90° male-to-female connectors

Hosa 3ft Right Angle XLR Cable 90° Male to Female

SKU CH-QN11-5BVPT

A 90-degree right-angle XLR cable connects balanced microphones or DMX gear with a male-to-female 3-pin layout

  • TypeXLR
  • ColorBlack
  • Length5 ft.
  • Connector Number1
  • Terminal GenderMale to Female
  • Specifications3.2, 3 feet, Male-to-Female, Round, Smays
  • Right-angle XLR saves space on tight stages
  • 90° male-to-female layout routes cleanly around gear
  • Balanced 24AWG OFC cores reject noise on long runs
  • Meets DMX standard for lighting and audio use
  • Zinc-alloy shells with strain relief survive repeated gigs

Right-Angle XLR for Tight Racks

This 3 ft balanced microphone cable uses a 90° male-to-female XLR connector to fit behind shallow racks, on crowded stages or inside compact podiums. The right-angle moulding reduces cable strain at the jack and keeps the run neat in permanent installs. It suits live sound, broadcast and fixed-installation work where straight plugs would foul adjacent gear.

DMX Standard and 24 AWG Construction

The cable meets the DMX standard so it can carry lighting-control data as well as audio. Conductors are 24 AWG oxygen-free copper (16 × 0.12 mm) in a twisted pair with aluminium foil and a 64 × 0.1 mm braided shield, all inside a 6.0 mm flexible PVC jacket. Gold-over-nickel contacts on zinc-alloy shells resist corrosion in touring and outdoor use.

Replaces Straight XLR Leads in Confined Spaces

Use this cable instead of a straight XLR lead when rack depth, wall plates or dense patch bays make a 90° exit necessary. The internal strain relief and rugged moulding survive repeated mating cycles better than bare solder joints. The jump is worth it whenever a straight connector would be bent, damaged or block neighbouring ports.

Highlights

  • Right-angle XLR saves space on tight stages
  • 90° male-to-female layout routes cleanly around gear
  • Balanced 24AWG OFC cores reject noise on long runs
  • Meets DMX standard for lighting and audio use
  • Zinc-alloy shells with strain relief survive repeated gigs

Specifications

BrandHosa
TypeXLR
ColorBlack
Length5 ft.
Connector Number1
Terminal GenderMale to Female
Specifications3.2, 3 feet, Male-to-Female, Round, Smays
Sports Team1 Piece
FeaturesSmays, 3 feet, 3.2, Male-to-Female, Round, outdoor, indoor

Questions about this item

Is the 3-foot length enough to reach from a floor stand to a mixer on a nearby table?

At exactly three feet the cable spans roughly one metre, which is long enough for a mic on a short stand to a desk-top mixer but leaves no slack for routing around gear.

Will the 24 AWG conductors and braided shield keep a microphone signal clean over this distance?

The 24 AWG oxygen-free copper cores plus aluminium foil and 64-strand copper braid give low resistance and strong rejection of hum and RF interference for typical stage or studio runs.

Can the 90-degree male plug fit into a recessed XLR jack on a crowded patch panel?

The right-angle male connector protrudes only about 3.2 cm from the panel face, so it clears adjacent sockets and reduces strain on the jack.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.