HighZer0 Electronics
HighZer0 Electronics RFANT05Z+M4 MHF4 10cm network antenna pair
Replaces weak internal Wi-Fi antennas on M.2 cards with a 10 cm adhesive-backed pair covering 2.4, 5, 5.8 and 6 GHz bands
- TypeWireless Card Antenna
- ColorMulticoloured
- FeaturesLightweight,Flexible,Adhesive Backing
- Replaces weak or missing internal WiFi antennas
- Compatible with MHF4, IPEX4, 4th Gen U.FL connectors
- Supports 2.4GHz, 5GHz, 5.8GHz, 6GHz WiFi and Bluetooth
- 5dBi omnidirectional gain, vertical polarization, 50 Ohm impedance
- 10cm low-loss RF1.13 cables with adhesive backing for tight spaces
Internal WiFi Antenna Pair for M.2 Cards
This HighZer0 Electronics RFANT05Z+M4 set replaces weak, damaged, or missing internal antennas in laptops, desktops, motherboards, routers, and small form factor builds. It connects to MHF4, IPEX4, and 4th Gen U.FL ports found on M.2 / NGFF wireless cards such as AX200, AX210, AX211, BE200, BE202, 9260NGW, 9560NGW, 8265NGW, and 7265NGW. The pair supports 2.4GHz, 5GHz, 5.8GHz, and 6GHz WiFi and Bluetooth applications with omnidirectional 2.5dBi gain and 50 Ohm impedance.
Peel-and-Place Install with Adhesive Backing
Each 10cm antenna cable has a pre-attached double-sided adhesive pad for secure placement inside tight chassis, laptop lids, or motherboard enclosures. Peel the liner and press the FPC/PCB radiator pad onto a clean surface to lock position, conceal wires, and route the low-loss RF1.13 coax through confined spaces. The only common error is ordering this MHF4 set for cards that use the smaller MHF1, IPEX1, or 1st Gen U.FL connectors found on many mini-PCIe Half-Mini HMW cards; compare your connector size before purchase.
Connector Compatibility Decides Fit
The single specification that determines whether this is the correct part is the antenna port type on your wireless card: these cables terminate in MHF4, IPEX4, and 4th Gen U.FL connectors only. They will not mate with MHF1, IPEX1, or 1st Gen U.FL ports used by many older mini-PCIe adapters. Verify the connector generation on your AX200, AX210, AX211, BE200, BE202, 9260NGW, 9560NGW, 8265NGW, or 7265NGW card before ordering.
Highlights
- Replaces weak or missing internal WiFi antennas
- Compatible with MHF4, IPEX4, 4th Gen U.FL connectors
- Supports 2.4GHz, 5GHz, 5.8GHz, 6GHz WiFi and Bluetooth
- 5dBi omnidirectional gain, vertical polarization, 50 Ohm impedance
- 10cm low-loss RF1.13 cables with adhesive backing for tight spaces
Specifications
| Brand | HighZer0 Electronics |
|---|---|
| Model | RFANT05Z+M4 |
| Type | Wireless Card Antenna |
| Color | Multicoloured |
| Features | Lightweight,Flexible,Adhesive Backing |
Questions about this item
How can I confirm the antennas are functioning correctly after installing them on an AX200 card?
Check signal strength and link speed in the OS network utility; a stable connection on 2.4 GHz, 5 GHz, 5.8 GHz or 6 GHz bands with low packet loss indicates the 2.5 dBi omnidirectional antennas are working as intended.
What does the package contain and is anything else required for installation?
The box includes one pair of 10 cm RF1.13 cables with FPC/PCB radiators and pre-applied double-sided adhesive pads; no extra parts are needed — just peel and stick onto a clean surface inside the chassis.
Which connector variant should I select for a BE200 M.2 module?
Choose the MHF4 / IPEX4 / 4th Gen U.FL version listed — it matches the BE200, AX210, AX211, 9260NGW, 9560NGW, 8265NGW and 7265NGW cards; avoid the older MHF1 / IPEX1 style used on mini-PCIe HMW cards.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
