We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Straight breakout cable SFF-8654 8i to eight SATA connectors 39.37in

Fervit

Fervit SFF-8654 8i to 8×SATA 12Gbps 30AWG 100ohm 39.37in sata cable

SKU CH-2JVG-P9W1V

Converts one SFF-8654 8i Slimline SAS port to eight straight SATA ports at 12Gbps using 30AWG 100ohm cable measuring 39.37in

  • Converts one SFF-8654 8i port to eight SATA ports for massive multi-HDD expansion
  • Delivers stable 12Gbps bandwidth for SATA HDDs, SSDs and RAID controllers
  • 30AWG low-loss copper with 100ohm impedance matching preserves signal integrity
  • Straight connectors enable direct, space-saving installation in standard rackmount chassis
  • 37in length provides neat internal routing for high-density storage nodes

SFF-8654 8i to eight SATA breakout

This cable converts a single SFF-8654 8i Slimline SAS port into eight straight SATA connectors for multi-drive expansion. It supports stable 12Gbps data transfer with SATA HDDs, SSDs and RAID controllers. The 30AWG copper conductors and precise 100ohm impedance matching preserve signal integrity across the link.

Builders adding many drives to one port.

The breakout design suits servers and workstations that need eight SATA devices from one slimline SAS connection. High-density storage nodes benefit from the direct straight-connector layout inside rackmount chassis. Buyers connecting only one or two drives will find a simple SATA cable more appropriate.

One-metre straight cable with matched impedance

The 39.37in length enables neat internal routing without excess slack in dense enclosures. Straight SATA plugs allow compact side-by-side insertion against backplanes or drive cages. The 100ohm impedance control and fine-gauge wire reduce signal loss at full 12Gbps throughput.

Highlights

  • Converts one SFF-8654 8i port to eight SATA ports for massive multi-HDD expansion
  • Delivers stable 12Gbps bandwidth for SATA HDDs, SSDs and RAID controllers
  • 30AWG low-loss copper with 100ohm impedance matching preserves signal integrity
  • Straight connectors enable direct, space-saving installation in standard rackmount chassis
  • 37in length provides neat internal routing for high-density storage nodes

Specifications

BrandFervit

Questions about this item

What controller or backplane provides the SFF-8654 8i Slimline SAS port this cable plugs into?

A RAID controller, HBA, or backplane with an SFF-8654 8i Slimline SAS connector supplies the single port that this breakout cable converts to eight SATA ports.

Will SATA drives limited to 6 Gbps still work when connected through this 12 Gbps breakout cable?

Yes, each SATA HDD or SSD negotiates its native link speed, so 6 Gbps drives operate normally while the cable supports up to 12 Gbps bandwidth.

How can I verify the 100 ohm impedance and 12 Gbps signal integrity after installing the 39.37 inch cable?

Check the RAID controller or HBA management utility for clean link negotiation at the expected speed and run a sustained read or write test to confirm error-free throughput.

New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.