We take cryptocurrency — so the coins you hold can buy real hardware.Pay in crypto, spend it on real hardware. Free insured shipping worldwide over $399. Plain, unbranded boxes, sent from Germany.Free insured shipping over $399. Your rate is locked for 30 minutes once checkout opens.Rate locked 30 minutes. Every item sealed, serial-checked and covered by a 24-month warranty.Sealed, 24-month warranty.

Saved items Sign in
Black 90-degree adapter with 20-pin motherboard header and USB 3.1 Type-E female port

EN-Labs

EN-Labs USB 3.0 19/20 Pin to USB 3.1/3.2 Type-E Adapter 90 Degree

SKU CH-M5KF-AQ3JZ

Converts a motherboard USB 3.0 19/20-pin header to a USB 3.1/3.2 Type-E front-panel connector with 10 Gbps speed and a 90-degree design

  • Connector TypeUSB to 20 pins
  • ColorBlack

Style Left Angled

  • Converts a 19 or 20 pin header to a USB 3.1/3.2 Type-E front-panel connector
  • Delivers up to 10 Gbps data throughput via the USB 3.1 Gen 2 header
  • Right-angle 90 degree design eases routing in tight chassis spaces
  • Works with common motherboards that have a USB 3.0 19 pin header
  • Plug-and-play operation requires no driver installation on Windows, Mac or Linux

Motherboard Header Adapter

This EN-Labs adapter converts a motherboard USB 3.0 19 or 20 pin header into a USB 3.1 or 3.2 Type-E female connector. It suits builders adding a front-panel USB-C bracket to a board that only has the older internal header. The compact black unit supports data rates up to 10Gbps. It is not compatible with USB 2.0 IDC connectors.

Plug-and-Play Operation

No driver installation is required for Windows XP, 7, 8, 10 in 32 or 64 bit versions, plus macOS and Linux. The bundle supplies the adapter itself; there are no extra cables, brackets or software discs included. This means the front-panel Type-C port gains 10Gbps capability immediately after the hardware is seated. Builders who need additional mounting hardware must source it separately.

90-Degree Installation Steps

The right-angle shape helps fit tight chassis corners, but the pins are fragile. The supplier stresses a strict sequence: power off the tower, unplug it, wait ten seconds, orient the male end correctly, then plug the adapter into the USB 3.0 header. Skipping the wait or forcing the connector can short pins, cause the device to go unrecognised, or trigger USB over-power warnings.

Highlights

  • Converts a 19 or 20 pin header to a USB 3.1/3.2 Type-E front-panel connector
  • Delivers up to 10 Gbps data throughput via the USB 3.1 Gen 2 header
  • Right-angle 90 degree design eases routing in tight chassis spaces
  • Works with common motherboards that have a USB 3.0 19 pin header
  • Plug-and-play operation requires no driver installation on Windows, Mac or Linux

Specifications

Connector TypeUSB to 20 pins
ColorBlack

Other versions of this model

5 more in the same range

Same family, different memory, cooler or clock — compare before you commit.

Questions about this item

Will the 19/20-pin motherboard header connector wear out after repeated front-panel plug cycles?

The adapter uses a standard IDC 20-pin male header rated for typical motherboard installation cycles; no user-serviceable parts are inside, so replacement is only needed if a pin is bent during fitting.

Does the 10 Gbps rating hold steady when the front-panel Type-E port runs at full speed for hours?

The link is limited to 10 Gbps by the USB 3.1/3.2 Gen 2 specification; sustained throughput will not exceed that ceiling.

Does the 90-degree Type-E connector run hot or draw extra power during all-day transfers?

The passive adapter adds no active circuitry, so it generates no measurable heat and draws no power beyond the connected device’s normal USB 3.0/3.1/3.2 consumption.

Also in this aisle

People compared these

Same shelf, same checkout — eight coins and a 30-minute rate lock.