EN-Labs
EN-Labs SATA3-LEFT30CM SATA III cable left 90° to 180° latch red 1.64ft
A left-angled 90° to 180° SATA III cable with latch locking, 1.64 ft long, using 26 AWG tinned copper conductors for up to 6.0 Gbps transfers
- TypeSATA III
- Length11" - 15"
- Cable Length1 ft.
- Connector Number2
- Connector Detail1 x SATA to 1 x SATA
- Terminal GenderFemale to Female
- Left-angled 90° to 180° connector fits tight drive bays
- Latching straight connector prevents accidental disconnection during vibration
- 26 AWG tinned copper conductors deliver 6.0 Gbps SATA III throughput
- 64 ft length reaches drives without excess cable slack
- Backwards compatible with SATA I and II host ports
SATA III left-angled cable for tight builds
This EN-Labs SATA III cable has a left-side 90-degree connector that turns toward a straight 180-degree latch connector. The 1.64ft length fits compact cases and drive cages where straight plugs would foul neighbouring components. It supports 6.0Gbps transfer rates and remains backwards compatible with earlier SATA ports.
Shielded copper conductors sustain rated speed
26AWG tinned copper conductors with full shielding keep signal integrity steady during prolonged transfers. The latch on the straight end locks the connection so vibration or cable routing cannot unseat the plug. Data throughput is ultimately limited by the attached drive and controller rather than the cable itself.
Replaces standard straight-to-straight SATA leads
Builders who cannot route a straight connector past a graphics card, cooler or drive bracket will benefit from the angled end. It is not suited for external eSATA ports or right-angled clearance needs. The red jacket aids cable identification in dense wiring looms.
Highlights
- Left-angled 90° to 180° connector fits tight drive bays
- Latching straight connector prevents accidental disconnection during vibration
- 26 AWG tinned copper conductors deliver 6.0 Gbps SATA III throughput
- 64 ft length reaches drives without excess cable slack
- Backwards compatible with SATA I and II host ports
Specifications
| Brand | En-Labs |
|---|---|
| Model | SATA3-LEFT30CM |
| Type | SATA III |
| Length | 11" - 15" |
| Cable Length | 1 ft. |
| Connector Number | 2 |
| Connector Detail | 1 x SATA to 1 x SATA |
| Terminal Gender | Female to Female |
| Specifications | - Connector : 7-pin SATA Left side-angled 90 degree to 180 Degree latching Receptacle "L" Type key connector - Supports SATA revision III up to 6 Gbps - Backwards compatible with SATA I, II ports - Cable length is 1.64ft,- 26AWG tinned copper conductors |
| Shielding | Yes |
| Conductor | Copper Conductor |
| Features | The SATA left side-angled 90 Degree to 180 Degree SATA III 6 Gbps Cable connects both newer SATA III and legacy SATA I, II drives to internal motherboards and host controllers. The straight connector has a latch to provide a secure connection in tight spaces. IT technicians always need a spare on hand as a troubleshooting tool. DIY gamers can quickly upgrade their computer for expanded storage. It is backed by a lifetime warranty and product support. |
Questions about this item
Does the cable generate any heat or noise when used continuously in a server?
No, it is a passive copper cable with shielding and no active components, so it produces no heat or noise during all-day operation.
What must my motherboard or controller provide for this cable to function?
A standard 7-pin SATA data port on the motherboard or host controller is all that is required.
Will the left-angled 90° to 180° connector fit alongside older SATA I or II drives I still use?
Yes, the cable is backwards compatible with SATA I and II ports, and the angled latch connector works in tight spaces next to legacy drives.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00114364BTC
In stock
