EN-Labs
EN-Labs P4IDE2EPS8PIN6 internal power cable 6 inch ATX P4 Molex to EPS 8pin 18AWG
Adapts a PSU with ATX P4 and Molex connectors to an EPS 8-pin motherboard socket using 18AWG tinned copper conductors over a six-inch length
- TypeCable Splitters
- ColorMulti-Color
- Length6" - 10"
- SpecificationsType: ATX P4 to EPS 8pin power adapter cable Wire Gauge: 18A
- Connector Number3
- Terminal GenderMale to Female
- Adapts a P4 and Molex PSU to an EPS 8-pin motherboard
- 18AWG tinned copper conductors carry 12V DC power reliably
- Short 6-inch length reduces cable clutter inside the case
- Combines CPU P4 and Molex connectors into one EPS 8-pin plug
- New condition ensures clean, undamaged connectors for a solid fit
What this cable does
This 6-inch adapter lets a power supply equipped with a 4-pin ATX P4 connector and a Molex 4-pin connector feed an 8-pin EPS motherboard socket. It bridges older PSU layouts to newer CPU power requirements without replacing the unit.
How the connectors work
One end combines a P4 female socket and a Molex male plug to draw 12 V DC from two PSU leads. The other end presents a single EPS 8-pin male connector that plugs directly into the motherboard CPU power header.
Installing and common issues
Route the short 6-inch length between the PSU cables and the motherboard socket, then seat both source connectors firmly. The tight bend radius in small cases can strain the 18 AWG wires, so avoid sharp folds and verify all three plugs click fully home before powering on.
Highlights
- Adapts a P4 and Molex PSU to an EPS 8-pin motherboard
- 18AWG tinned copper conductors carry 12V DC power reliably
- Short 6-inch length reduces cable clutter inside the case
- Combines CPU P4 and Molex connectors into one EPS 8-pin plug
- New condition ensures clean, undamaged connectors for a solid fit
Specifications
| Brand | En-Labs |
|---|---|
| Model | P4IDE2EPS8PIN6 |
| Type | Cable Splitters |
| Color | Multi-Color |
| Length | 6" - 10" |
| Specifications | Type: ATX P4 to EPS 8pin power adapter cable Wire Gauge: 18AWG Tinned Copper Cable Length: 6 inch Connector A: 1 x ATX CPU P4 Female 1 x Molex 4pin Male Connector B: 1 x EPS 8pin Male Voltage:12V DC |
| Connector Number | 3 |
| Terminal Gender | Male to Female |
| Features | ATX 4 Pin CPU P4 to 8 Pin EPS Power Supply Cable Adapter, 6inch Converter cable that allows a PSU with a 4 pin Female P4 12v AUX Power connector with a Molex 4pin to be used with a motherboard that requires an 8 pin Male EPS connector. |
Questions about this item
How often should the 18AWG tinned copper conductors be inspected or replaced?
The 18AWG tinned copper wires are rated for continuous 12V DC use; inspect them only if insulation damage or connector looseness appears during routine system maintenance.
What is the first limit reached when the adapter runs at full load for long periods?
The 6‑inch length and 18AWG gauge set the practical current limit; sustained loads near the PSU’s P4 and Molex ratings will hit voltage‑drop and thermal limits before the cable itself fails.
How much heat does the 6‑inch adapter generate when powering an EPS motherboard all day?
With 18AWG tinned copper carrying 12V DC, heat stays low under normal CPU loads; the short 6‑inch run minimises resistance, so the cable remains barely warm during continuous operation.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
WMtec
WMtec 45 RPM vinyl record adapter silver aluminium 38mm 12mm 7.5mm
- Accessories
$14.99
0.00018068BTC
In stock
DELL
DELL 93XWF Intel Quick Assist Adapter 8970 100 Gbps 23W PCI-E 3.0 x16 Bracket
- Bracket
$21.99
0.00026506BTC
In stock