EN-Labs
EN-Labs 3PINSPL26 TX3 3-pin fan splitter cable 10 in 24AWG
Splits one 3-pin fan header into two 3-pin fan connections with 10-inch sleeved cables and 24AWG copper conductors
- TypeCable Splitters
- ColorBlack
- Length6" - 10"
- Cable Length10 in.
- SpecificationsType :TX3 3Pin case fan power splitter cable, Length: 6 inch
- Connector ATX3 3Pin Female
- Connect two 3-pin fans to one header
- 10 inch length reaches fans without strain
- 24AWG copper conductor delivers reliable power
- Black braided sleeve protects wires and looks clean
- One header carries full speed signal, other runs two wires
Splitter for two 3-pin fans
This TX3 3-pin splitter connects two case fans to a single motherboard or power-supply header. It is built for builders who need an extra fan connection without adding a fan controller. The cable carries 12 V or 5 V power to both fans from one source. It suits systems with limited 3-pin headers.
24 AWG copper with braided sleeve
The 10 inch cable uses 24 AWG copper conductors wrapped in a black net-jacket sleeve. One female TX3 connector plugs into the header; two male TX3 connectors attach to the fans. Only one male header carries all three pins for speed feedback, the other carries two pins for power only. The sleeve protects the wires during routing.
One header reports speed, the other does not
Because the second male header lacks the tachometer wire, only the first fan reports its speed to the motherboard. PWM 4-pin fans are not supported on either connector. Builders who need independent speed control for both fans cannot use this splitter. The 10 inch length suits typical case layouts but may fall short in large enclosures.
Highlights
- Connect two 3-pin fans to one header
- 10 inch length reaches fans without strain
- 24AWG copper conductor delivers reliable power
- Black braided sleeve protects wires and looks clean
- One header carries full speed signal, other runs two wires
Specifications
| Brand | En-Labs |
|---|---|
| Model | 3PINSPL26 |
| Type | Cable Splitters |
| Color | Black |
| Length | 6" - 10" |
| Cable Length | 10 in. |
| Specifications | Type :TX3 3Pin case fan power splitter cable, Length: 6 inches, Conductor:26AWG Copper Connector A:1 x 3pin fan TX3 female, Connector B: 2 x 3pin Fan TX3 male, Power supports:12V/5V fans |
| Connector A | TX3 3Pin Female |
| Connector B | TX3 3Pin Male |
| Connector Number | 3 |
| Terminal Gender | Female to Male |
| Features | This TX3 Fan Power Splitter Cable lets you connect two 3-pin (TX3) fans to a single power supply connector, allowing you to optimize your cooling capability without having to upgrade the power supply. Use this 1 x 3-pin motherboard header to power 2 x cooling fans with 3-pin connector. Female end 3-pin header plugs into motherboard 3pin/4pin header ( or fan power header from power supply), 2 x 3-pin male headers to cooler fans. Dual Male headers for 3Pin Fans only, incompatible with PMW 4pin Fans One of 3pin male header is equipped 3 power wires, the other 3pin male header is just in |
Questions about this item
Does the 3-pin TX3 splitter work with 12 V and 5 V fans?
Yes, the cable supports both 12 V and 5 V fans through the TX3 connectors.
What clearance is needed for the 10-inch sleeved cable and dual male headers?
The 10-inch length with black net jacket sleeving fits standard case fan spacing; both male headers are TX3 3-pin.
How do I install the splitter so the speed signal works correctly?
Plug the female TX3 end into the motherboard or PSU header, then connect the 3-wire male header to the fan that must report RPM.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00114711BTC
In stock
