EN-Labs
EN-Labs 2pcs Anodized Black Aluminum Heatsink 28x28x20mm DIY Cooling
Pair of low-profile aluminium fin heatsinks measuring 28×28×20 mm for chipset, GPU or power-component cooling
- ColorBlack
- CompatibilityMotherboard Chipsets
- MaterialAluminium
- FeaturesAnodized Black Aluminum heatsink for Computer General northb
- Dimensions28 x 28 x 20mm
- Two-piece kit covers multiple chipset zones
- Anodized black aluminium dissipates heat efficiently
- Low-profile 28 × 28 × 20 mm footprint fits tight spaces
- Fins increase surface area for greater heat transfer
- Light 30 g mass adds minimal board load
Anodized Aluminium Heatsink Pair
This pack supplies two low-profile aluminium heatsinks finished in anodised black. Each unit measures 28 x 28 x 20 mm and weighs about 30 g. They are designed for DIY cooling of motherboard chipsets such as northbridge and southbridge controllers. The parts can also be attached to graphics-card components, power transistors, FETs, ICs, voltage regulators or small audio amplifiers.
Replaces Stock Clip-On Spreaders
The heatsinks upgrade from basic flat metal spreaders or bare silicon by adding finned surface area for better passive dissipation. The improvement is worthwhile when the original cooler is missing, damaged or too tall for the available clearance. Installation requires thermal adhesive, which is not included, so buyers must source a suitable glue or epoxy separately.
28 mm Square Footprint With 20 mm Height
The 28 mm square base covers typical chipset packages while the 20 mm fin stack provides extra radiating area without exceeding a low-profile envelope. This size comfortably handles chipset and VRM loads in confined spaces such as small-form-factor boards or multi-GPU slots. It runs out of capacity on high-wattage CPUs, large GPU cores or any component exceeding the 28 mm mounting footprint.
Highlights
- Two-piece kit covers multiple chipset zones
- Anodized black aluminium dissipates heat efficiently
- Low-profile 28 × 28 × 20 mm footprint fits tight spaces
- Fins increase surface area for greater heat transfer
- Light 30 g mass adds minimal board load
Specifications
| Color | Black |
|---|---|
| Compatibility | Motherboard Chipsets |
| Material | Aluminium |
| Features | Anodized Black Aluminum heatsink for Computer General northbridge ,Southbridge Cooling ,also can be used for cooling graphics card, vidoe card,motherboard, power transistor, FET, IC, power amplifier, Voltage Regulator,etc. The fins increase the area of the board and thus provide for greater heat transfer. Use heatsink adhesive glue to install heatsink on the IC.Glue is not included here. Size is 28mm x 28mm x 20mm low profile , Please check the specification table and make sure that the size of the heatsink fits that of your component. Specification Product Name: Heatsink Material: A |
| Dimensions | 28 x 28 x 20mm |
Questions about this item
Will the 28 x 28 x 20 mm footprint clear my motherboard's chipset area?
The heatsink measures 28 mm long, 28 mm wide and 20 mm tall, so compare those dimensions with the clear space around your northbridge or southbridge chip before buying.
What is the correct way to attach the heatsink using thermal adhesive?
Clean the chip surface with isopropyl alcohol, apply a thin, even layer of heatsink adhesive glue (not supplied), press the finned side down firmly, and let the glue cure fully before powering on.
Does the anodised finish need any upkeep over time?
The black anodised aluminium surface is corrosion-resistant and requires no maintenance; simply blow dust out of the fins with compressed air if airflow becomes restricted.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Black Box Corporation
Black Box Corporation CAT6 EZ-RJ45 Modular Plugs 100-Pack
$95.99
0.00114814BTC
In stock
