Innovation First, Inc.
Innovation First, Inc. 1UCMA-137 1U Cable Management Arm 19" 28.5"-33" computer accessory
- Product Type:Cable…
- Panel Width:19" Rac…
$72.99
0.00086162BTC
In stock
Cables To Go
Cables To Go 50210 VGA Cable 1 ft M/M CMG In-Wall
A 1 ft VGA cable with CMG-rated jacket for in-wall installation, HD-15 male connectors on both ends, and full 15-pin wiring for DDC2 and EDID support up to 2048x1536 resolution
- TypeCable Connectors
- ColorBlack
- Length1 ft
- Connector Number1
- Connector DetailConnector on First End:1 x HD-15 Male VGA Connector on Secon
- SpecificationsDevice Supported:Monitor Projector Video Device
- CMG-rated jacket meets in-wall fire-safety codes
- 2048 x 1536 resolution delivers sharp QXGA video
- All 15 pins wired for DDC2 and EDID support
- Low-profile connectors fit tight projector mounts
- One-foot length keeps short runs tidy
In-wall VGA cable for monitors and projectors
The Cables To Go 50210 is a 1 ft male-to-male VGA cable built with a CMG-rated jacket for in-wall installation. It connects monitors, projectors or other video devices using standard HD-15 connectors. The short length suits tight runs inside conduit or behind mounted displays where a CMG rating is required.
Low-profile connectors simplify tight installs
Rounded, low-profile HD-15 ends fit into narrow spaces such as projector mount poles without straining the jack. All 15 pins are wired to carry DDC2 and EDID data so the source can read the display’s capabilities. The CMG jacket meets in-wall fire codes while remaining flexible for routing through studs.
No adapters or software included
The package contains only the cable itself; no drivers, configuration tools or extra adapters are supplied. Compatibility relies on the host and display supporting VGA signalling up to 2048x1536 resolution. Buyers needing longer runs, active signal boosting or digital interfaces such as HDMI or DisplayPort must source those separately.
Highlights
- CMG-rated jacket meets in-wall fire-safety codes
- 2048 x 1536 resolution delivers sharp QXGA video
- All 15 pins wired for DDC2 and EDID support
- Low-profile connectors fit tight projector mounts
- One-foot length keeps short runs tidy
Specifications
| Brand | C2G |
|---|---|
| Model | 50210 |
| Type | Cable Connectors |
| Color | Black |
| Length | 1 ft |
| Connector Number | 1 |
| Connector Detail | Connector on First End:1 x HD-15 Male VGA Connector on Second End:1 x HD-15 Male VGA |
| Specifications | Device Supported:Monitor Projector Video Device |
| Features | Cable Type: VGACable Length: 1 ftConnector on First End: 1 x 15-pin HD-15 Male VGAConnector on Second End: 1 x 15-pin HD-15 Male VGADevice Supported: Video Device,Monitor,ProjectorColor: BlackWeight (Approximate): 68 gLimited Warranty: Lifetime |
| Cable Length | 0.5 ft. |
| Shipping weight | 0.07 kg |
| Package size | 140 × 140 × 13 mm |
Questions about this item
How do I install the 1 ft VGA cable in a wall cavity, and what is the common mistake?
Run the CMG-rated jacket through studs or conduit and secure with low-voltage brackets; the mistake is stripping the jacket too far back, which removes the in-wall fire rating.
What maintenance or replacement will the 50210 cable need over time?
Inspect the HD-15 connectors for bent pins and the jacket for abrasion; replace the cable if any pin is damaged or the CMG jacket shows cuts.
At what resolution limit does the cable show its constraint first during sustained use?
The cable supports up to 2048x1536 resolution; beyond that the signal degrades first, so keep the source at or below QXGA.
New to this? Which coin should you pay with — what to check, what it costs to pay, and what is never asked for.
Also in this aisle
People compared these
Same shelf, same checkout — eight coins and a 30-minute rate lock.
Vertiv
Vertiv 4UTELECOMRKIT 19 in rack mount bracket accessory
- GXT4U Wall Mount Br…
- Mounting Bracket
$70.99
0.00083801BTC
In stock
